• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Best connecting rods??

  • Thread starter Thread starter 1SLO306
  • Start date Start date Feb 10, 2006
1

1SLO306

My 97 GTP owns you ALL!
Mar 31, 2005
904
1
17
Muhlenberg, ky
Feb 10, 2006
#1
  • Feb 10, 2006
  • #1
ive been looking into a rebuild using the stock 302 block and crank. I think im going to go with the Forged TRW .030 pistons. What are the best Rods?? Should i go forged with them as well??? All opinions welcome!
 

1991GreeNLX

New Member
Jul 2, 2004
129
0
0
Houston TX
Feb 10, 2006
#2
  • Feb 10, 2006
  • #2
i have eagle H-beam rods
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 10, 2006
#3
  • Feb 10, 2006
  • #3
I bought the Eagle "SIR I-Beam" rods. good for up to 500hp in a small block, and they are bushed for $285.95. i guess it depends on how you are rebuilding ecaxtly. if you are wanting a giant blower or a ton of nitrous, you might just want to go with H beam rods. Mine is N/A and my machine shop said i would be fine with the I Beams.
 
8

87'GTstang

New Member
Feb 16, 2004
1,025
0
0
Feb 10, 2006
#4
  • Feb 10, 2006
  • #4
Most rods are forged anyway due to them having to endure the highest level of stress in an engine - which leads me to the point, don't buy junk in this department.
Eagle are hard to beat, Manley is another good manufactuer of good quality.
 
8

87'GTstang

New Member
Feb 16, 2004
1,025
0
0
Feb 10, 2006
#5
  • Feb 10, 2006
  • #5
FarBeyondDriven said:
I bought the Eagle "SIR I-Beam" rods. good for up to 500hp in a small block, and they are bushed for $285.95. i guess it depends on how you are rebuilding ecaxtly. if you are wanting a giant blower or a ton of nitrous, you might just want to go with H beam rods. Mine is N/A and my machine shop said i would be fine with the I Beams.
Click to expand...
I went with the same rods when I built my engine.
I'll go ahead and lay the slap in your face with this site I lucked out on with:
http://www.cnc-motorsports.com/category.asp?CtgID=3182
Even better was I got them $21 less than the advertisement now when I bought them
 

JIffy94

New Member
May 17, 2003
58
0
0
Arvada Colorado
Feb 10, 2006
#6
  • Feb 10, 2006
  • #6
I really doubt a rod will go before the block will. The time the rods recieve the most stress is when its going over tdc and the rod literally wants to stretch....putting a blower or turbo on the motor could actually increase a rods strength. Instead of using the crank to draw it down, the boost will be of a slight aid.....Using a stock block build i would just do stock rods with ARP connecting hardware....
 

stang8urimport

Autozone Junkie
Founding Member
Jun 21, 2002
1,499
12
59
Daytona Beach, FL
Feb 10, 2006
#7
  • Feb 10, 2006
  • #7
I agree. The block will break before the stock rods or crank will. Put the money into something worth while.
 
1

1SLO306

My 97 GTP owns you ALL!
Mar 31, 2005
904
1
17
Muhlenberg, ky
Feb 10, 2006
#8
  • Feb 10, 2006
  • #8
ok, thanks guys. i think ill keep the stockers until i build something radical(which may be when i 30 LOL)
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Feb 10, 2006
#9
  • Feb 10, 2006
  • #9
Yep, keep the stockers. Get them resized...
 

vikingpower

New Member
Dec 6, 2004
656
0
0
CWU Ellensburg, WA
Feb 10, 2006
#10
  • Feb 10, 2006
  • #10
If you've done your reading on 5.0 buildups, there's been a lot of 500+ whp engines using the stock rods and crank. Just gotta keep the RPMS under 7000.
 
1

1SLO306

My 97 GTP owns you ALL!
Mar 31, 2005
904
1
17
Muhlenberg, ky
Feb 10, 2006
#11
  • Feb 10, 2006
  • #11
i doubt my car will ever see anything close to 7k
 
3

304billet

Member
Sep 16, 2005
315
1
16
Feb 10, 2006
#12
  • Feb 10, 2006
  • #12
I would not use TRW pistons. Either SRP, Ross, CP, or Probe pistons. stick with major brands.

Eagle and Scat r the leaders in offshore 4340 crank and 4340 rods, quality stuff good to 1000fwhp. With ARP 2000 rod bolt upgrade good to 1200fwhp. Stick with the majors.
 

352Ford2

New Member
Oct 12, 2005
393
0
0
Seattle,WA
Feb 10, 2006
#13
  • Feb 10, 2006
  • #13
Dude, TRW is a very major brand. The factory forged pistons in our cars are made by TRW, and most performance aftermarket pistons (the ones under 600 bucks a set) are made from TRW blanks. Yes they are not quiet as nice as the high end JE's or Ross's, but they are a good bang for the buck, by the way the easiest way to get TRW's these days is just get the Speed pros.
 

stang8urimport

Autozone Junkie
Founding Member
Jun 21, 2002
1,499
12
59
Daytona Beach, FL
Feb 10, 2006
#14
  • Feb 10, 2006
  • #14
304billet said:
I would not use TRW pistons. Either SRP, Ross, CP, or Probe pistons. stick with major brands.

Eagle and Scat r the leaders in offshore 4340 crank and 4340 rods, quality stuff good to 1000fwhp. With ARP 2000 rod bolt upgrade good to 1200fwhp. Stick with the majors.
Click to expand...
If TRW isn't MAJOR, I dunno what is. They make a LOT of OEM pistons.
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Feb 13, 2006
#15
  • Feb 13, 2006
  • #15
87'GTstang said:
I went with the same rods when I built my engine.
I'll go ahead and lay the slap in your face with this site I lucked out on with:
http://www.cnc-motorsports.com/category.asp?CtgID=3182
Even better was I got them $21 less than the advertisement now when I bought them
Click to expand...


Have i mentioned lately that i cant STAND YOU!!!!!
 
8

89white50

Member
Nov 16, 2004
440
1
18
central MA
Feb 13, 2006
#16
  • Feb 13, 2006
  • #16
Dude, TRW is a very major brand
Click to expand...

HAHA, for sure. That about as big as you can get. As to the person with the Hawks racing rods, they did seem to be good quality? i was planning on thier I beams for my stock block 331 build. I figured since its all forged and i have to get it balanced whats the difference right?
 

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Feb 13, 2006
#17
  • Feb 13, 2006
  • #17
I re-used the stockers in my motor, i just had em resized and used ARP hardware. I also went with JE's SRP pistons, and the quality was very impressive. The guy that balanced my rotating assembly said they were very consistent and the motor runs very very smooth. No real need for aftermarket rods in a stock block motor. I've heard the stock rods will handle just about 450 hp, which is all the block is safely good for. good luck
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Feb 13, 2006
#18
  • Feb 13, 2006
  • #18
That setup will do fine for a stock blocked combo.
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
730
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
My next project , a 428 build!
  • horse sence
  • Jul 29, 2026
  • Classic Mustang Specific Tech
  • 9 10 11
Replies
215
Views
5K
Classic Mustang Specific Tech Tuesday at 1:24 PM
horse sence
A
Engine 04 GT timing chain issue
  • AwesomeX1103
  • Sep 3, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
565
SN95 4.6L Mustang Tech Nov 5, 2025
Noobz347
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
513
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?