Black Jack: Dragstrip tuning. New records

Well, I went out today to refill the bottle. Swapped in my 2nd bottle. I made 2 Hwy pulls. No change. It still ran low 10s on both banks. Swapped fuel jet from .036 to .034. Still low tens, even saw 9.9AFR. What gives? Guess I'll go back to .032? This is not maiing sense to me.
 
  • Like
Reactions: rednotch
I still think it can match it or better that mph and et on the smaller .054 nitrous jet the kit came with when the fueling is dialed in.

The jetting has me seriously thinking the selonids internal passage is more of a restriction than the .067 jet though just based on mph gain and afr readings. I go off the plugs when dialing in jetting not afr though, I can't find what selonid they use in that box but there tiny as seen in the video earlier.


.052 .031 is basically my starting point for 100+ real rear wheel gain with a HCI sbe with what ever cobbled together single nozzle kit I throw on. Usually end up with a .028 fuel jet for most and never even nipped a gasket on shot that small. all ways got at least 10mph gain over na trap speed in the 1/4. So your 117 pass is about where I would expect to be with a with a smaller nitrous jet.

Like I said factory recommended jetting is very fat on all most all kits and the other zex kits with larger selonids then what you have is recommending .067 /.038 as a 150 shot, that is on the larger side for jetting, a .067 jet as the only restriction is usually enough pph for 175ish hp gain using a single nozzle.. most suggest a .062 nitrous jet for a 150 shot. Fuel jetting is based on flowing fuel pressure so they vary wildly from the factory recommended jetting charts by companies based on what car and its factory fuel pressures. But this is why I think the jet isn't the restriction but your selonids are. . Your starting with the .067 jet and testing the fuel and haven't even come close to lean yet. If we go a page back you said you ran 115 on the 100 shot jetting, actually said it was 100 nitrous 125 fuel in notes. So .046 N and .034F, you just saw afr in the low 10's with that fuel jet and a 067 nitrous jet, a .021 jump in the nitrous jet on the same fuel jet. thats something that also points to a restriction on the nitrous side other than the jet. I would definitely swap the .067 nitrous jet out and start with the largest .054 nitrous jet your kit came with and us that as the base line to dial in the fuel jetting. The .054 jet is more than capable of flowing enough nitrous to meet or beat your current best when it's dialed in.
 
True, I did crack 115 before. I used the same fuel jet back then, but I think that was also before I started tuning with the Quarterhorse, and my NA pulls were in the 13.5:1 range. So, pulling the AFR down to the 11.5 range took more fuel than pulling it down from the mid 12s, now.

To be fair, that was also still 2.7 mph slower than this weekend's best, and this weekend was with the car weight about 100 lbs heavier. So, if I can lock in the AFR I see potential for 119 mph, though maybe 4mph isnt enough to expect from such a large N2O jet. On the dyno, that "100 shot" only picked up 65rwhp... very disappointing. And, the trap speed gain reflected it. Turning 114 - 115 best, as compared with 108 mph NA, a gain of 6 - 7, right in line with the dyno gains. This weekend, I picked up 11.5 mph same day, same track.

I take your point, though, and I'm not opposed to dropping down to establish a baseline with consistent fueling.

Supposing the solenoids I have suck, does an oversized nitrous jet actually cause problems, or does it just maximize what the kit can do? This also makes me wonder if I can just replace Zex's NMU with one that has bigger solenoids. I should not have let the speed shop sell me this one when I explicitly told them I wanted to run a 150 shot. I'll call Zex to ask if they have an easy upgrade.
 
Last edited:
True, I did crack 115 before. I used the same fuel jet back then, but I think that was also before I started tuning with the Quarterhorse, and my NA pulls were in the 13.5:1 range. So, pulling the AFR down to the 11.5 range took more fuel than pulling it down from the mid 12s, now.

To be fair, that was also still 2.7 mph slower than this weekend's best, and this weekend was with the car weight about 100 lbs heavier. So, if I can lock in the AFR I see potential for 119 mph, though maybe 4mph isnt enough to expect from such a large N2O jet. On the dyno, that "100 shot" only picked up 65rwhp... very disappointing. And, the trap speed gain reflected it. Turning 114 - 115 best, as compared with 108 mph NA, a gain of 6 - 7, right in line with the dyno gains. This weekend, I picked up 11.5 mph same day, same track.

I take your point, though, and I'm not opposed to dropping down to establish a baseline with consistent fueling.

Supposing the solenoids I have suck, does an oversized nitrous jet actually cause problems, or does it just maximize what the kit can do? This also makes me wonder if I can just replace Zex's NMU with one that has bigger solenoids. I should not have let the speed shop sell me this one when I explicitly told them I wanted to run a 150 shot. I'll call Zex to ask if they have an easy upgrade.
You massively over looking the fact it was the same fuel jet your running now but with a .021 larger nitrous jet and still rich, with the quaterhorse, A .067 jet as the restriction can flow enough for 650 PPH.. that's about 200hp tuned clean. You start looking at water grains over DA when pushing the limits on nitrous. Your na tuning is not going to change the N/F ratio of what your spraying into the motor as it's pressure based, nitrous flow is rated at PPH. You always want the jet to be the restriction, not the selonid, not the lines, the jetting is at the nozzle for a reason and that jetting was pig rich. look at what the fuel jetting did to the mph at your last outing both in 1/8 and 1/4. So your not comparing clean data.

The zex Nozzle will flow more than 150, that we know, it uses the fat shank jets like nx, ns, no, Tnt and the old compucar, I used pretty much all of them mixed and matched I just pin gauge mine to make sure they are whT the say, NOS is the thin, long style, have a few of those nozzles to.

We know the kits rated to handle the. 054 jet, you want clean data, right now your just guessing at what the nitrous side can flow unless you physically measure the PPH or check the internal passage sizes. Selonids can also get trash in them and not fully open or stick. A stand alone rebuildable selonid is way better then dealing with pre packaged nmu's, that's only controlling tps activation.. I literally have 30 plus yr old parker selonids I still use and have rebuilt a few times. Most brands sourced them from Peter Paul Electronics or Parker and they go for profit so they get the cheapest they think they can get away with and make a sizable profit off them.


Swapping the selonids is as easy as replacing them with better ones. Would have to rewire It threw the box to keep it Tps activated though. Zex is edelbrock group, now, just like Holley its PE owned and they gutted most of the knowledge and product line from the companies so you will probably be dealing with a min wage phone jockey reading canned responses to up sell you.
 
Last edited:
  • Like
Reactions: 85GTStangGuy
My MSD 3 in 1, which I already wired in, will take care of the TPS activation and window switch. I'm listening, brother. I'll back off and re-establish baseline.
Stepping back to a .054 jet isn't that downgrade you think it is once it's cleaned up, it should be trapping around right with your best so far. That's lower 11's range if you can get it too hook, but stick shift and radials take some real skill to work for a good 60ft in a full weight car. Have you ever tried that jetting yet or did you jump from the .046 to the .067. Its also the no money option outside of t&t and bottle fills since we know it works with what you all ready have. A bottle heater is a good idea if you don't have one, you want consistent pressure, you can make one cheap and easy as hell now since you can grab heating pads out of modern cars seats in pick in pulls.
 
  • Like
Reactions: FastDriver
Yessir. I have a bottle heater that plugs into my cigarette lighter. It was cold out there, but a half full bottle got down to ~850 psi by the end of the night. It takes an hour or so, but brings bottle pressure up to the 950 - 1k psi range, when the bottle is full.

Not sure whether I tried the .054, but I went from the .046 to the .067 between mid June & early July 2024. I had some notes indicating that I researched a couple zex kits, one of which called for a .064 and one called for a .067 to get to a 150 shot. So, I tried both.

I've got to get a DS safety loop on the car, but I've already got my speed shop ordering 15x10 Welds RTS wheels that I hope will clear the Cobra brakes. They've agreed to test fit em before I purchase. If they work, I'm pretty well set on trying the Mickey 3053S stiff wall 26x15" tire. So, I am planning on going to a slick.

I thought the 1.80 60' was a decent start. I still have double-adjustable shocks/struts, 2-step & seat time (non-adjustable clutch foot work) adjustments to hopefully improve the 60' some more on the Nittos.
 
Last edited: