• Community Forums
  • Regional Forums and Event Information

Braided Line/AN Fitting Expert Wanted

  • Thread starter Thread starter N20Jnky
  • Start date Start date Mar 26, 2007
N

N20Jnky

Founding Member
Mar 28, 2002
721
1
0
Mar 26, 2007
#1
  • Mar 26, 2007
  • #1
Hey Guys:

Been a looooooong time, but I'm finally getting back to putting the N20Jnky back together with the 408 under the hood... Had some hellish fittment problems, but I think I have them solved...

I am running an Aeromotive fuel system and I am looking for someone that is an expert at cutting and putting on AN fittings to throw a couple of bucks at. I need someone to cut the lines and put fittings on about 5 lines...

Any experts out there want to either earn a few bucks, or perhaps come over spend a little time in my new home shop (3-bay with lift) and down a few beer while putting some lines together???

Let me know...

BTW - As FE pointed out, it might be a good idea to tell where I am located... UHG!!!!!

Between Snohomish and Monroe on Highway 2...

Thanks....
 

FE_NUT

New Member
Dec 13, 2005
60
0
0
BRUSH PRAIRIE, WA.
Mar 26, 2007
#2
  • Mar 26, 2007
  • #2
Where are you located?

The pacific nw is a mighty big area.
 
N

N20Jnky

Founding Member
Mar 28, 2002
721
1
0
Mar 26, 2007
#3
  • Mar 26, 2007
  • #3
Good point...

I am North of Seattle in the Snohomish/Monroe area...

Thanks!!!
 

stock50LX

Curmudgeon
Founding Member
Oct 2, 2001
1,858
0
0
University Place, WA
Mar 26, 2007
#4
  • Mar 26, 2007
  • #4
So, Earl is still alive! Are you getting that 408 on the track this season?
 
N

N20Jnky

Founding Member
Mar 28, 2002
721
1
0
Mar 26, 2007
#5
  • Mar 26, 2007
  • #5
John:

I am still alive... It has been so long!!!

In the interim we moved up near Monroe... Why you ask -- because I now have a 2,600 square foot shop with a lift!!!!

I don't want to say that I am going to get the car to the track this summer, because sure enough, something will come up and it won't happen, but that is my intention...

Brandon was over last weekend and we totally mocked up the car... Installed the motor, the tranny and the exhaust... Then we fitted the hood... Amazingly, it all fit!!!! I am going to have to buy a different K-Member... I need one with a 3/4" motor and steering rack drop... We also figured out how to run the Aeromotive fuel lines...

Once I get that installed, then I will be ready to drop the motor in... I will then have to remember how to put all the wires back together... Oh God!!! I cut them 3 years ago... Let's hope that I coded them well!!!!!

Lastly there will be some interior work... New carpet, reconfigured hatch with center battery box, etc....

Then -- to the shop to have the brakes redone, and the motor fired and tuned....

If you run into someone that is crack at putting AN fittings on braided line, and cutting braided line, tell them that I have a six pack waiting for them if they would give me a hand in the next two months...

Good to see that you are still around and I truly hope to see you this summer...
 

stock50LX

Curmudgeon
Founding Member
Oct 2, 2001
1,858
0
0
University Place, WA
Mar 27, 2007
#6
  • Mar 27, 2007
  • #6
That is a long "to do" list. I wish I could help you with the braided lines, but I opted for the rubber ones (still NHRA legal).

That is a huge shop! You must have other toys inside. It can't all be for your fox body! Keep us posted on your progress.
 
You must log in or register to reply here.

Similar threads

3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
598
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
1
Engine Motor swap from a 2003 Explorer
  • 1996mustang new
  • Oct 9, 2025
  • SN95 4.6L Mustang Tech
Replies
7
Views
620
SN95 4.6L Mustang Tech Oct 16, 2025
squeak93
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
530
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
SN Mustang Magnum T56 swap
  • revhead347
  • May 24, 2024
  • 1994 - 1995 Specific Tech
Replies
15
Views
6K
1994 - 1995 Specific Tech Jun 28, 2026
GearHeadGuy
Fuel Replacing the Plastic Factory Fuel Line Push on Connectors
  • AeroCoupe
  • Mar 16, 2023
  • Fox 5.0 Mustang Tech
  • 2
Replies
28
Views
28K
Fox 5.0 Mustang Tech Mar 23, 2023
rednotch
Share:
Bluesky Email Share Link
  • Community Forums
  • Regional Forums and Event Information
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?