• Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
  • 2005 - 2009 Specific Tech

Brenspeed Detroit Rockers

  • Thread starter Thread starter FR-S8N
  • Start date Start date Jul 4, 2011

FR-S8N

Founding Member
May 23, 2002
1,306
0
0
McAllen, tx
Jul 4, 2011
#1
  • Jul 4, 2011
  • #1
Anybody have these?

I'm thinking about getting them for my car. Only setback would be if I have to upgrade my stall converter. If I do then the cams would be a no go.
Hoping for nice idle with gains.

Mods done are in my sig, and I have a light weight driveshaft sitting in my garage right now just waiting for installation.

EDIT: Around how much does a cam sap cost? I've been out of the game for a while now.
 

jpplaw

Member
Jan 14, 2009
185
3
18
Jul 4, 2011
#2
  • Jul 4, 2011
  • #2
I have the Detroit Rocker blower grinds. You can definitely tell there are cams in there at idle. If you are running 4.10's you definitely won't have to upgrade your T/C. I run fine with a stock auto and 3.31's, just some minor bucking during extreme low speed driving, i.e. lower than 1000 rpms. May take some tweaking to the tune for idle air and dashpot settings (throttle closing rate) to get it the way you like it.
 
L

lungbuster

New Member
Jun 19, 2011
6
0
1
Jul 21, 2011
#3
  • Jul 21, 2011
  • #3
I also have them and they were great with the 331 gear and as well when I swapped to the 410 gears as far as the cams go there are no other required mod to run these but I will say at idle my car runs very fat rich. When I asked brenspeed about it they said that just how the cams run. I hope you like black tail pipes lol
 
You must log in or register to reply here.

Similar threads

J
Transmission
  • Jraesims
  • Mar 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
181
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 8, 2026
JD1964
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
256
Other Auto Tech Jul 13, 2026
General karthief
C
C4 trans help needed
  • CPH89LX
  • Apr 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
214
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 28, 2026
CPH89LX
C
S
Preparation for Holley Terminator X install – Foxbody 306 (electrical fan, alternator, MSD Ignition, etc)
  • So_Flo
  • Mar 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 4, 2026
General karthief
Hard to start when engine is cold
  • 86_Capri
  • Mar 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
985
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
  • 2005 - 2009 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?