• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

bump compression on 75' 351W

  • Thread starter Thread starter importhater5.0
  • Start date Start date Oct 4, 2007
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 4, 2007
#1
  • Oct 4, 2007
  • #1
Ive got a 351W im throwin in my 90' Notch. Stock bottom end and conn. rods, bored .040 over with stock flat top pistons. Im trying to decide on a head and piston combo. I was thinking of getting Edelbrock Victor Jr. heads...2.05 and 1.60s. They have 60cc comb. chambers. SO what i wanted to do is swap out the pistons and get the comp. ratio up to 10 or 10.5:1. Does anyone have any recommendations on pistons. ALso, can i just the stock conn. rods. thanks
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 4, 2007
#2
  • Oct 4, 2007
  • #2
What I would do...

Shave the heads to reduce the chamber volume, and bump the CR.
Work with what you have now.

jason


EDIT:
Unless there is a decent budget for the build????????
 

Fast63

New Member
Sep 20, 2007
717
0
0
Oct 5, 2007
#3
  • Oct 5, 2007
  • #3
I would not shave the heads because you can mess up the intake alignment. Just doing the heads will get your compression in the 9.5 range, or higher depending on what kind of stock piston you have already. If you really want to get that extra compression, change the pistons and use any flat top piston that has two valve relieves that will get you to the compression you desire (I cannot give any recommendations because there are many out there and I don't know your budget or anything. It would be best for you to contact a place like summit racing to find out what is best.) You should be able to use the stock rods on any piston that has the same pin diameter, but you'll probably have to have the pistons pressed out and the new ones pressed in by a machine shop, unless you can do it yourself.
 
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 9, 2007
#4
  • Oct 9, 2007
  • #4
would it be more cost effective to have the stock pistons machined for the valve reliefs, or just buy new flat tops with the reliefs already in them? thanks for the suggestions guys!
 

samickguy15

Member
Sep 1, 2005
404
0
16
Delavan, IL
Oct 9, 2007
#5
  • Oct 9, 2007
  • #5
I just bought a set of forged Keith Blacks for my 351W, shipped to my door for $270. They're also .040. They're the 9925's which should bump my compression with the GT-40P heads to about 10.2:1. Exactly where I want it!
 
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 9, 2007
#6
  • Oct 9, 2007
  • #6
ok cool! ill have to check those out
 
I

iapexl8r

Member
Apr 1, 2005
254
0
17
Oct 9, 2007
#7
  • Oct 9, 2007
  • #7
throw a stroker kit at it 408 your comp will increase with flat top pistons. go for it .
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Oct 9, 2007
#8
  • Oct 9, 2007
  • #8
I have dished pistons in my 351w. I think I'm bellow the 8.5 to compression ratio. I wish I had flat tops.
 
I

importhater5.0

New Member
May 15, 2003
94
0
0
West Chester, Pa
Oct 9, 2007
#9
  • Oct 9, 2007
  • #9
Hey Blue Cobra, what year is your block? Obviously, mine being a '75 is a hydraulic flat tappet. What would be the best route? Keep it flat tappet, go to mechanical flat tappet, or switch it to a roller? I saw in your pics that you had Comp roller rockers so i was just wondering if you had a mid 90's block or did you convert your ol school block. I have also been trying to figure out what heads to go with, i would like to go with the Victor Jrs. so i have room for upgrades and wont have to buy another set of heads later, so the 2.08 and 1.60 valves should be plenty for my plans. My other question is if i put some flat top pistons with dual valve reliefs, will the reliefs be big enough for a 2.08 intake valve? Ive tore apart my 302 HO multiple times, but this is my first time screwing with a flat tappet engine so im trying to get a plan and head in the right direction, because i dont know what i can and cant use on it. any help is appreciated guys!
 
You must log in or register to reply here.

Similar threads

R
Progress Thread 351w stroker rotating assembly and build
  • Ric4eyedFox
  • Mar 23, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 24, 2025
Noobz347
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
Engine Raising compression on a relatively stock 302
  • keel
  • Jul 9, 2023
  • Fox 5.0 Mustang Tech
Replies
16
Views
9K
Fox 5.0 Mustang Tech Jul 20, 2023
keel
SBF Head Flow Table - Work in Progress
  • Noobz347
  • Sep 29, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
17
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 30, 2025
Noobz347
SOLD SOLD!!!! 1993 Notchback Roadracer For Sale. She's a beast!
  • Boydster
  • Apr 25, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
1K
Fox Body Mustangs For Sale (1979-93) Apr 25, 2025
Boydster
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?