• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Burnt Brake Piston Boots

  • Thread starter Thread starter go-stang5.0
  • Start date Start date Feb 20, 2006

go-stang5.0

New Member
Jan 27, 2003
2,244
0
0
Glenview,Il
Feb 20, 2006
#1
  • Feb 20, 2006
  • #1
HEy guyz I'm running pbr cobra calipers up front and when I went to Gingerman Roadcourse in Michigan last October I set my street brake pads on fire. Anyways I got around to taking the brakes off today (for pad replacement) and I noticed that there was a material burned off the dust boots. One piston on each side had a boot burned. Anyways, the calipers only have like 20k miles so I dont really need a rebuild...I was just wondering if it was ok to run the calipers with the boots burned. I know its not the greatest thing to do but I am planning on a rebuild next year so. I was just wondering if I would be ok till then. After all there just "dust boots". Gimme your opinions...thanks guyz.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Feb 21, 2006
#2
  • Feb 21, 2006
  • #2
See if you can pick up a caliper rebuild kit anyway. I'd be more than willing to bet that the structural integrity of the pistons may be compromised, after having gotten hot enough to catch the brake pads and dust boot on fire. Plus, without the boots being intact, you could potentially contaminate the inside of the caliper and brake fluid with anything that's small enough to fit inside, including water.
 

go-stang5.0

New Member
Jan 27, 2003
2,244
0
0
Glenview,Il
Feb 21, 2006
#3
  • Feb 21, 2006
  • #3
I ordered a rebuild kit today when I went to get my rotors cut. The pistons seem fine, there are no singe marks on them or anything (just a bit dirty from not having a boot on them). Also the system is not leaking so the seal has not failed. I think the pistons are fine...This morning I called BAER and they recommended that I rebuild the caliper and the guy at the auto parts store said the same thing...So I guess I will do that tonight. I dont have a compressor so I was planning on blocking 3 of four pistons and pumping the brake pedal to pop out the unblocked one and replaing the seal and boot there and then moving on to the next one....and doing the whole system that way. I know it will be messy and I will have to bleed the system but is there any reason I should not do it this way?
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Feb 21, 2006
#4
  • Feb 21, 2006
  • #4
Nah, that way should work just fine. I did that when my rears were frozen in the bore, even though they're only single piston calipers. I just hit the bore with some emery cloth and clean brake fluid, popped the piston back in, and it's been good for over a year since.
 

Labora

Founding Member
Jun 11, 2000
1,854
26
69
Dallas, Texas
Oct 22, 2007
#5
  • Oct 22, 2007
  • #5
If you did this yourself how in the hell do you get the dustboots on correctly without ripping them? I've messed up 2 of them just trying to do it.


(Bump to old thread cus this is the closest topic I could find)
 

Labora

Founding Member
Jun 11, 2000
1,854
26
69
Dallas, Texas
Oct 22, 2007
#6
  • Oct 22, 2007
  • #6
Ok got them on finally, my suggestion for future readers. Put the boot on the piston then slide it to the bottom, then work the bottom of the boot into the ridge. If it is too wet (you are supposed to add brake fluid to the rings per ford service book) they will not stick.

Fought it for 3 hours yesterday while they where too wet only to get them to pop in first time today because they where dry.
 

go-stang5.0

New Member
Jan 27, 2003
2,244
0
0
Glenview,Il
Oct 22, 2007
#7
  • Oct 22, 2007
  • #7
Wow...this takes me back. Yea if you push the piston in all the way it gets a bit easier. I used toothpicks to help the boots along, but I have since come across dental picks. You can get them from many road racing type websites (as odd as that sounds). THey make for very handy dust boot installation for future refrence. I still destroy dust boots every track day so i gave up on it. I run without them and just rebuild the calipers once a year. I also bleed the calipers before every track day and flush the entire brake system every year. Its a lot easier with dental piks....trust me.
 
You must log in or register to reply here.

Similar threads

SOLD SOLD!!!! 1993 Notchback Roadracer For Sale. She's a beast!
  • Boydster
  • Apr 25, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
1K
Fox Body Mustangs For Sale (1979-93) Apr 25, 2025
Boydster
Brakes Clicking noise while braking?
  • TIGGER
  • Sep 26, 2022
  • Fox 5.0 Mustang Tech
  • 2
Replies
37
Views
7K
Fox 5.0 Mustang Tech Feb 26, 2023
TIGGER
M
Gt convertible brake problems.
  • MacMAgoo
  • Oct 2, 2022
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
12
Views
3K
1996 - 2004 SN95 Mustang -General/Talk- Oct 15, 2022
CAMTWO1070
Just dreamin'
  • FastDriver
  • May 6, 2023
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
902
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 6, 2023
FastDriver
Front brakes locked up.
  • Sonicstang0494
  • Dec 1, 2020
  • SN95 4.6L Mustang Tech
Replies
3
Views
2K
SN95 4.6L Mustang Tech Jan 2, 2021
Sonicstang0494
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?