• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Cam Degree Never Happened

  • Thread starter Thread starter 93lxdm78
  • Start date Start date Jul 15, 2007
9

93lxdm78

New Member
Jun 19, 2007
71
0
0
Jul 15, 2007
#1
  • Jul 15, 2007
  • #1
I recently installed a new cam in my engine actually a friend of mine did and we never degreed the cam car seem to be running fine.

Do I need to tear it down again and have that done or should I just leave it
 

TheBocSez

New Member
Feb 3, 2004
652
0
0
Converse, TX
Jul 15, 2007
#2
  • Jul 15, 2007
  • #2
did you guys at least line of the dots on the crank and cam sprockets? If so, I think you will probably be ok. Maybe not optimal but fine.
 
9

93lxdm78

New Member
Jun 19, 2007
71
0
0
Jul 15, 2007
#3
  • Jul 15, 2007
  • #3
Yes that we did do.
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Jul 16, 2007
#4
  • Jul 16, 2007
  • #4
You'll be fine. In fact, there's a chance that it's actually perfect the way it is given manufacturing errors.
 

TheBocSez

New Member
Feb 3, 2004
652
0
0
Converse, TX
Jul 16, 2007
#5
  • Jul 16, 2007
  • #5
I agree, I think youll be fine. Thats all most people do anyway.
 
9

93lxdm78

New Member
Jun 19, 2007
71
0
0
Jul 16, 2007
#6
  • Jul 16, 2007
  • #6
Oh man cool thanks guys I feel better now
 

Jaswir

Member
Mar 31, 2005
578
0
18
Orlando, FL
Jul 16, 2007
#7
  • Jul 16, 2007
  • #7
yea most people dont degree the cam, which ur supposed to with the degree wheel.... everyone just pops it in and lines up the dots...
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Jul 16, 2007
#8
  • Jul 16, 2007
  • #8
haha. you do not need to degree the cam in. Unless of course your some big time drag racer that goes to the track all the time trying to beat your time by tenths of a second. Line up the dots and your good to go.
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Jul 17, 2007
#9
  • Jul 17, 2007
  • #9
ShortThrow50; said:
haha. you do not need to degree the cam in. Unless of course your some big time drag racer that goes to the track all the time trying to beat your time by tenths of a second. Line up the dots and your good to go.
Click to expand...

Don't be mistaken. Although he should be fine he may have left quite a few ponies on the table by not degreeing the cam in. Even cheap engine dyno software will confirm that moving a cam just 3 or 4 degrees can result in over a 10 HP difference. There are reasons that identical combos can have wildly different results at the track and it's not all in the drivers. Attention to detail is the difference between having an okay performer and having a winner. Degreeing the cam and getting a dyno tune when everything is done and put together can make a huge difference.
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Jul 17, 2007
#10
  • Jul 17, 2007
  • #10
Maryland Stang said:
Don't be mistaken. Although he should be fine he may have left quite a few ponies on the table by not degreeing the cam in. Even cheap engine dyno software will confirm that moving a cam just 3 or 4 degrees can result in over a 10 HP difference. There are reasons that identical combos can have wildly different results at the track and it's not all in the drivers. Attention to detail is the difference between having an okay performer and having a winner. Degreeing the cam and getting a dyno tune when everything is done and put together can make a huge difference.
Click to expand...

true. Perhaps my wording was a little straight forward. Very true though my friend. All in all this guy will be fine though
 
You must log in or register to reply here.

Similar threads

1
Crank no start on a turbo and cammed pushrod 5.0
  • 1630stri
  • Sep 2, 2026
  • Digital Self-tuning Forum
Replies
2
Views
214
Digital Self-tuning Forum Sep 16, 2026
Qtrhrse23
K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
238
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
519
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
D
Engine HO cam in non HO roller block ‘93 f150
  • DanC1993f150
  • Mar 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
525
Fox 5.0 Mustang Tech Mar 29, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?