cam selection

bill302 · Sep 21, 2007

im thinking about installing a bigger cam,i have never selected a cam and i'm lost on this subject....i'm looking for 300 horse power n/a with my combo listed in my signature......thanks..below is what im looking at...good bad or ugly?

Part Number: 444222 Grind Number: POWERMAX 2030 (FORMERLY COM
Engine Identification:
Start Yr. End Yr. Make Cyl Description
1985 Up FORD-MERCURY 8 H.O.
Engine Size Configuration
302 C.I. V

Valve Setting: Intake .000 Exhaust .000 HOT

Lift: Intake cam 333 @Valve 533 All Lifts are based
on zero lash and theoretical rocker arm ratios.
Exhaust @ Cam 340 @Valve 544
Rocker Arm Ratio 1.60

Cam Timing: --- @---
Lift: Opens Closes ADV Duration
Intake --- --- 270 °
Exhaust --- --- 278 °

Spring Requirements: Triple Dual Outer Inner
Part Number 99841
Loads Closed 113 LBS @ 1.950 or 1 61/64
Open 338 LBS @ 1.430
Recommended RPM range with matching components
Minimum RPM 1400
Maximum RPM 5400
Valve Float 6000

Cam Timing: TAPPET @.050
Lift: Opens Closes Max Lift Duration
Intake 1 BTDC 35 ABDC 107 216 °
Exhaust 47 BBDC (7) BTDC 117 220 °

Remarks:
FIRING ORDER: 1-3-7-2-6-5-4-8

final5-0 · Sep 21, 2007

I also am not all that schooled on cams other than just basic info
but
I have looked at many, many different OEM block combos
with a NA focus when talking about application

Now ... if that 300 value you used is about rwhp

It is very unlikely you are gonna reach that goal with E7's
and
Cam selection is not gonna make all that much difference

True ... those E7's have been ported
but
It is still gonna be tough to do it

I'm not all that fond of the Cobra intake
but
Since it has been ported ... that can make a difference

Let me finish with this line of thought

I'd say its possible to reach 300 rwhp
but
The power band is gonna be quite peaky
and
That is not all that great for a NA Street Car ... IMHO

Please ... Don't think I'm trying to be negative

I am just trying to be realistic based upon other results I've seen

Grady

5spd GT · Sep 21, 2007

300 at the engine - yes

300 at the wheels - no

Bill, have you ever thought of a custom cam. They could also tune some exhaust bias for that little shot you have...

That cam is a bit bias as well on the exhaust side, typically set for those stock style heads, like what you have. A custom cam, would net you better gains, as I'm sure you know.

martfr2 · Sep 21, 2007

Final 5-0 & 5spd GT are correct, I would probably save the extra cash & pick up a set of heads (AFR) and a custom cam you'll see 300+...I am running AFR185 with stock bottom end pistons had to be notched it was a pain in the A$$, E303, & Cobra Intake I made 321 on the dyno. My dyno guy said intake was holding me back about 10-15 HP. Just my 2 cents...saving up for a 331 from CHP

Shooter in So. Cal

donkey_punch · Sep 21, 2007

i have the 2031 it pretty much the same but for 1.7 rockers (cause i have a cobra)
but i also have AFR 165.
my suggestion go bigger and if you decide on heads go bigger. lol
its a mild cam, you will notice a difference it will pull hard to 5500 rpm, but nothing to do backflips over.
from what i was told from the guy who suggested the cam was that it was a good cam for nitrous ( not idealy "a nitrous cam") and pretty good for a SC down the road. i would assume it would be the same for the 2030 as for the 2031

there so much out there, if i had to do it again. i would call every cam company's tech line and ask a million questions and ask for suggestions to reach your goal.

good luck
joe

bill302 · Sep 25, 2007

well anyone else? has anyone run this cam cause i think im going to get it....also how would i adjust the factory rocker arms would it be as follows (same as stock)Rotate the crankshaft until the tappet is resting on the heel (base circle) of the camshaft lobe tighten to 25 lbs.

earleys94gt · Sep 26, 2007

bill302 said:
also how would i adjust the factory rocker arms

The factory pedastal mount rockers arn't adjustable.

I have factory E7's with 1.96/1.60 valves, with a Steeda 19 (.480 lift) .
From what I understand, with the factory bottom ened, this is the highest lift
you can go. Someone correct me if I am wrong .

The others are right on that with ported E7's, 300 whp probably won't happen.
But with bigger valves maybe.

Check out Thumper's site for info...www.thumperoforangepark.com

cam selection

bill302

Active Member

final5-0

Mustang Master

5spd GT

"the 5.0 owns all"

martfr2

New Member

donkey_punch

New Member

bill302

Active Member

earleys94gt

Active Member

Similar threads

cam selection

bill302

Active Member

final5-0

Mustang Master

5spd GT

"the 5.0 owns all"

martfr2

New Member

donkey_punch

New Member

bill302

Active Member

earleys94gt

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency