Can you identify this 351w motor? some questoins

DarkoStoj

Founding Member

Sep 4, 2002

929

13

39

Detroit

Jan 29, 2004

#1

• Jan 29, 2004

• #1

i bought this motor a little while ago and i beleive it came out of a early 90's truck of some sort, but I have no idea. It is fuel injected and runs off a serpentine belt. I need to get a flywheel for it and am trying to figure out whether or not i would need a 28 oz, 50oz or any other type of flywheel.

anybody know anything good/bad about the fuel injection setup that is already on there?

 

Edbert

Founding Member

Jul 13, 2002

3,548

32

109

Austin TX

Jan 29, 2004

#2

• Jan 29, 2004

• #2

DarkoStoj said:

anybody know anything good/bad about the fuel injection setup that is already on there?

Click to expand...

Other than the fact that the induction ports seem to be infested with dessicated fingers (!!!!)?

 

DarkoStoj

Founding Member

Sep 4, 2002

929

13

39

Detroit

Jan 29, 2004

#3

• Jan 29, 2004

• #3

well what else can you use to keep crud out of the ports? I have no idea?????

 

H

hindle

New Member

Jan 9, 2004

28

0

0

Flemington, NJ

Jan 29, 2004

#4

• Jan 29, 2004

• #4

Are there any numbers on it?

 

brianj5600

Active Member

Sep 19, 2003

1,964

2

39

Middle TN

Jan 29, 2004

#5

• Jan 29, 2004

• #5

All 351s are 28 oz balance. You need to know what size bell housing you have, 164 or 157. Choose wrong and your starter won't line up. I have an extra 164. I believe 164 = 14.5in and 157 = 13.25in., or you can count.

 

67coupestang

Founding Member

May 31, 2002

509

2

19

Jan 29, 2004

#6

• Jan 29, 2004

• #6

well all 351W's are 28 oz. you would be corect its from a truck. the injection thats on it is crap, and probably wont fit under your hood anyways. there is a small chance it could be a roller block though, i think like 94+ maybe

 

DarkoStoj

Founding Member

Sep 4, 2002

929

13

39

Detroit

Jan 29, 2004

#7

• Jan 29, 2004

• #7

well this isn't going into a stang... got my 347 for that. This is actually going into a competition rockcrawling rig.

so i need to find myself a 28oz flywheel, and would it matter if i used a 10.5" or 11" clutch? I need to find a ford bellhousing that has a bolt on slave cylinder somewhere, and im pretty sure those are all from trucks so looks like i might need the 11" but not sure

 

D

D.Hearne

New Member

Sep 29, 2000

11,730

6

0

south louisiana

Jan 30, 2004

#8

• Jan 30, 2004

• #8

67coupestang said:

well all 351W's are 28 oz. you would be corect its from a truck. the injection thats on it is crap, and probably wont fit under your hood anyways. there is a small chance it could be a roller block though, i think like 94+ maybe

Click to expand...

Hey, don't be puttting down my 351's injection system like that. It certainly ain't "crap". Over 130K miles and it's never failed to start cause it was crap. Runs strong too in my 95 E150, it ain't the fastest off the line, but the topend is terrific, still haven't found the top yet.Sounds great too after you remove the silencer, just like a good old fashioned 4 bbl.

 

67coupestang

Founding Member

May 31, 2002

509

2

19

Jan 30, 2004

#9

• Jan 30, 2004

• #9

sorry i was just refering to efi for horse power... I wish i could use it on my 76 bronco, but it wont fit under the hood of that either...

 

D

D.Hearne

New Member

Sep 29, 2000

11,730

6

0

south louisiana

Jan 30, 2004

#10

• Jan 30, 2004

• #10

Two words: HOOD SCOOP!!!!

 

D

D.Hearne

New Member

Sep 29, 2000

11,730

6

0

south louisiana

Jan 30, 2004

#11

• Jan 30, 2004

• #11

Hell even a regular air cleaner on a 302 wouldn't clear a Bronco's hood!!!

 

dolfan87

Founding Member

Dec 28, 2000

1,242

0

0

Lake Havasu, AZ

Jan 30, 2004

#12

• Jan 30, 2004

• #12

My uncle has a roller EFI 302 in a 72 Bronco, and the hood shuts. It came out of a T-bird.

Just FYI