• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Car Runs Really Hot

  • Thread starter Thread starter influence
  • Start date Start date Oct 9, 2008
  • 1
  • 2
Next
1 of 2 Next Last
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#1
  • Oct 9, 2008
  • #1
I have a 91 5.0 it runs really hot

PWR Aluminum Radiator
Electric Fan
Upgraded Alternator
180 deegree thermostat

It usually runs at...welll Im assuming 235-245 degrees its ridiculous...it used to spew coolant till I figured the perfect radiator and overflow levels....but it still runs hot.

The fan is thermo activated once it hits 160 degrees.

This ticks me off...besides the numerous other issues I have

Thanks in Advance
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 9, 2008
#2
  • Oct 9, 2008
  • #2
Do you have an aftermarket temp gauge?

When does it run hot? While idling or while at speed?
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#3
  • Oct 9, 2008
  • #3
Both at idle it will get to about 200 degrees, that is sitting for a bit though, but when I drive it gets hotter.


I also just changed the plugs, did a radiator flush and engine flush, changed the oil and a new thermostat(180).

There is no smoking of the motor, the oil is clean, and no coolant oil mix on dipstick or or in radiator.

It is the stock temp quage with a brand new sending unit.
 
L

LxVert

Member
Dec 26, 2003
80
0
6
Oct 9, 2008
#4
  • Oct 9, 2008
  • #4
Is your fan turning on when it's supposed to and staying on? I tried one of those automatic fan sensors before and found the thing to be garbage.
 

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Oct 9, 2008
#5
  • Oct 9, 2008
  • #5
Seems like a flow issue. Do you have underdrive pulleys. Maybe get a 93 cobra WP pulley. Its an overdrive setup and it will flow more water through the radiator.
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#6
  • Oct 9, 2008
  • #6
The Fan actually works great I have it set to come on at about 160, it stays on the entire time , long after I shut off the car. I do not have any aftermarket pulleys on the car. I will look into the cobra pulley, though thanks
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 9, 2008
#7
  • Oct 9, 2008
  • #7
You need another means of checking temperature than the stock gauge. Otherwise, you have no idea where you're at.

If you are indeed at 200*F while idling and higher thereafter, something is systemically wrong or you have multiple issues. Be sure the t-stat is opening fully, and doing so when it should.
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#8
  • Oct 9, 2008
  • #8
Is there anyway you can clue me in on a few things to start checking?

The thermostat is new and Housing
The Water Pump is new
The Radiator is New
The Fan is new
The Serpentine Belt is New
The Motor has 60k on it

I would love to start narrowing this down because it is irritating.

Thanks
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 9, 2008
#9
  • Oct 9, 2008
  • #9
influence said:
Is there anyway you can clue me in on a few things to start checking?

The thermostat is new and Housing
The Water Pump is new
The Radiator is New
The Fan is new
The Serpentine Belt is New
The Motor has 60k on it

I would love to start narrowing this down because it is irritating.

Thanks
Click to expand...

New t-stat doesnt = good t-stat. Be sure it opens fully by 190*F or so.
Be sure the system is bled properly.
Be sure the air dam under the car is present.

Be sure your fan is spinning the correct direction. It should pull air towards the engine (away from the radiator).

And again, you NEED to have a real gauge. The stocker is not accurate, nor accurate enough for diagnostics. A mech gauge from the parts store is about 20 bucks.

Good luck.
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#10
  • Oct 9, 2008
  • #10
Thank You...I will begin to investigate all this, I appreciate all the help.
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Oct 9, 2008
#11
  • Oct 9, 2008
  • #11
what fan do you have exactly? I remeber on my dads cobra, he had the same problem as you, it turned out the electric fan was not strong enough to cool. Also, be sure your not wired wrong and blowing the air outward. Funny as this sounds, it happens, make sure it is pulling air from the outside into the engine compartment.
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 9, 2008
#12
  • Oct 9, 2008
  • #12
It is a flexalite I believe, I cannot remember it is fairly large fan almost covers the entire radiator
 

d1coupe

New Member
Oct 3, 2008
5
0
0
Oct 9, 2008
#13
  • Oct 9, 2008
  • #13
influence said:
It is a flexalite I believe, I cannot remember it is fairly large fan almost covers the entire radiator
Click to expand...

what the cfm on the it ??? It may no be enough!
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 10, 2008
#14
  • Oct 10, 2008
  • #14
Ill have to check and Ill get back to you.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 10, 2008
#15
  • Oct 10, 2008
  • #15
I would not worry about the fan right now. It runs hot at idle and gets hotter once at speed (where the fan doesnt even matter).
 

d1coupe

New Member
Oct 3, 2008
5
0
0
Oct 10, 2008
#16
  • Oct 10, 2008
  • #16
HISSIN50 said:
I would not worry about the fan right now. It runs hot at idle and gets hotter once at speed (where the fan doesnt even matter).
Click to expand...

your correct and incorrect yes it WILL run if it needs to! and IF the fan cannot support what the car needs for cooling then that will be a problem. My father has a speed shop and you wont believe how many people change from a clutch fan to a electric fan and put the wrong size on... or better yet the fan just does its job and something silly as a air dam removed, bags, or just one really hot day- will have you chasing your tail! So the fact that he doesn't know the cfm size could be the reason this all started but now its not the problem!

but you still need to go thru the steps to figure out A) the problem and B) what caused it!

check the basic:
1) do you have a leake or Bad head gaskets! You can buy a cheep pressure tester!
2) do you have a worn belt tensioner, or a bad belt..... YES the water pump pulley will slip!
3) is my water pump bad?
4) can my fan pull enough air?
5) did i remove the air dam or is something causing a blockage?
6)is the radiator anygood?

Sounds like you killed the head gaskets and it pressurizing the cooling system...
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Oct 10, 2008
#17
  • Oct 10, 2008
  • #17
d1coupe said:
your correct and incorrect yes it WILL run if it needs to! and IF the fan cannot support what the car needs for cooling then that will be a problem. My father has a speed shop and you wont believe how many people change from a clutch fan to a electric fan and put the wrong size on... or better yet the fan just does its job and something silly as a air dam removed, bags, or just one really hot day- will have you chasing your tail! So the fact that he doesn't know the cfm size could be the reason this all started but now its not the problem!

but you still need to go thru the steps to figure out A) the problem and B) what caused it!

check the basic:
1) do you have a leake or Bad head gaskets! You can buy a cheep pressure tester!
2) do you have a worn belt tensioner, or a bad belt..... YES the water pump pulley will slip!
3) is my water pump bad?
4) can my fan pull enough air?
5) did i remove the air dam or is something causing a blockage?
6)is the radiator anygood?

Sounds like you killed the head gaskets and it pressurizing the cooling system...
Click to expand...

+1. You need to check on that fan asap. The fan my dad was using was a flexlite. Like i said also be sure it is blowing the right direction
 
I

influence

New Member
Feb 3, 2007
46
0
0
Oct 10, 2008
#18
  • Oct 10, 2008
  • #18
If I did blow the head gaskets wouldnt there be some sort of oil/coolant mixture in the radiator or coolant resevoir or on the dipstick/ oil cap?

I think the fan is 2450 CFM

It is a fairly new PWR Radiator with approx 1000 miles on it.

I just replaced the belt should I try to get a hair smaller belt to make it tighter?
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Oct 10, 2008
#19
  • Oct 10, 2008
  • #19
influence said:
If I did blow the head gaskets wouldnt there be some sort of oil/coolant mixture in the radiator or coolant resevoir or on the dipstick/ oil cap?

I think the fan is 2450 CFM

It is a fairly new PWR Radiator with approx 1000 miles on it.

I just replaced the belt should I try to get a hair smaller belt to make it tighter?
Click to expand...

not all the time buddy. I had a bad head gasket and none of those symptoms. The way i knew it was blown was becuase my coolant sysytem was being pressurized, causing the coolant to spew out of the overflow. You can check to see if there is coolant in your oil by changing the oil. Since the oil will obviously sit on top of the coolant, you will want to look real closely right after you pull the drain plug. The coolant will be the first thing to come out. I doubt that u will find any on the dipstick since it sits on the bottom.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 10, 2008
#20
  • Oct 10, 2008
  • #20
d1coupe said:
your correct and incorrect yes it WILL run if it needs to! and IF the fan cannot support what the car needs for cooling then that will be a problem. My father has a speed shop and you wont believe how many people change from a clutch fan to a electric fan and put the wrong size on... or better yet the fan just does its job and something silly as a air dam removed, bags, or just one really hot day- will have you chasing your tail! So the fact that he doesn't know the cfm size could be the reason this all started but now its not the problem!

but you still need to go thru the steps to figure out A) the problem and B) what caused it!

check the basic:
1) do you have a leake or Bad head gaskets! You can buy a cheep pressure tester!
2) do you have a worn belt tensioner, or a bad belt..... YES the water pump pulley will slip!
3) is my water pump bad?
4) can my fan pull enough air?
5) did i remove the air dam or is something causing a blockage?
6)is the radiator anygood?

Sounds like you killed the head gaskets and it pressurizing the cooling system...
Click to expand...

How am I incorrect? He has an issue or cannot reject enough heat, even while ambient air flow is sufficient. People are focusing on his fan, when any fan he uses will not fix the heat-rejection issue. If the fan was the issue, he would cool nicely at speed but heat up while stationary.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

Engine Themostat
  • Mindseye007
  • Jan 30, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
1K
Fox 5.0 Mustang Tech Feb 1, 2026
86HO5.0
8
Resolved Got Too Hot!!!
  • PonyGTrider
  • Apr 27, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
759
Fox 5.0 Mustang Tech May 6, 2025
PonyGTrider
M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
Engine Help diagnose random overheating??
  • TomOsiris
  • Apr 10, 2022
  • Fox 5.0 Mustang Tech
  • 5 6 7
Replies
122
Views
17K
Fox 5.0 Mustang Tech Jul 3, 2023
General karthief
My saga of keeping the car running cool
  • hoopty5.0
  • May 19, 2022
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 20, 2022
hoopty5.0
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?