• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2.3L (N/A & Turbo) Tech

Car Will NOT Start.....

  • Thread starter Thread starter 4turboho
  • Start date Start date Mar 15, 2009
4

4turboho

New Member
Jan 31, 2009
119
0
0
Mar 15, 2009
#1
  • Mar 15, 2009
  • #1
I have a 91 mustang 2.3 and tuesday night, I was driving and I started to slow down and the car died on me. I got the car towed and looked at it and I discovered the belt was loose then changed it and saw all the grooves were ate off. I replaced it. Ive replaced this belt "atleast" 5 times on other 2.3l never had a problem. Car wont start. I have takin this belt on and off ten to twelve times The timing marks are one hundred percent dead on!! But still wont run Is there something else that could have happened here that im not looking at? thanks for any advice.
 

Red_LX

I’m not much help unless you’re looking for ****!
Founding Member
Nov 29, 1999
5,896
73
129
Morgantown, WV...where couches meet their doom
Mar 16, 2009
#2
  • Mar 16, 2009
  • #2
Does it at least sound like it has compression while you're cranking?
 
4

4turboho

New Member
Jan 31, 2009
119
0
0
Mar 16, 2009
#3
  • Mar 16, 2009
  • #3
Red_LX said:
Does it at least sound like it has compression while you're cranking?
Click to expand...

yea it does
 
D

dreamer1uk

New Member
May 9, 2008
33
0
0
Mar 29, 2009
#4
  • Mar 29, 2009
  • #4
Hi,

Did you check for codes? Also, im assuming that you allready checked for fuel and spark?
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Mar 29, 2009
#5
  • Mar 29, 2009
  • #5
no start

4turboho said:
I have a 91 mustang 2.3 and tuesday night, I was driving and I started to slow down and the car died on me. I got the car towed and looked at it and I discovered the belt was loose then changed it and saw all the grooves were ate off. I replaced it. Ive replaced this belt "atleast" 5 times on other 2.3l never had a problem. Car wont start. I have takin this belt on and off ten to twelve times The timing marks are one hundred percent dead on!! But still wont run Is there something else that could have happened here that im not looking at? thanks for any advice.
Click to expand...

had this happen to me when i was young..it was an 88 turbo coupe...we messed up with the spark plugs on the dizzy..we had #1 right but didnt have direction right on cap...dah
 
R

RustBucket

New Member
Jun 8, 2003
585
0
0
Buford, GA
Mar 30, 2009
#6
  • Mar 30, 2009
  • #6
He won't have that problem on the '91.
 
4

4turboho

New Member
Jan 31, 2009
119
0
0
Mar 31, 2009
#7
  • Mar 31, 2009
  • #7
RustBucket said:
He won't have that problem on the '91.
Click to expand...

I wouldnt have the cap problem but if I didnt hook them up right on the coil pack it wont run........oh and by the way the crankshaft sensor broke.
 
D

dreamer1uk

New Member
May 9, 2008
33
0
0
Mar 31, 2009
#8
  • Mar 31, 2009
  • #8
Hi,

Im glad you fixed the problem! How did you find out the issue? using a OBD 1 scanner?
 
4

4turboho

New Member
Jan 31, 2009
119
0
0
Mar 31, 2009
#9
  • Mar 31, 2009
  • #9
dreamer1uk said:
Hi,

Im glad you fixed the problem! How did you find out the issue? using a OBD 1 scanner?
Click to expand...

well i tried the scanner but i let me battery run dead and and when i ran the scanner the only code it would pull was it noticed the battery had been disconnected...so I could smell gas while I would try to crank it so I checked spark none....so I checked the coil packs..good! checked the ignition module bad! theres my problem! Wrong... then I found out if the crank shaft sensor is broke you wont get fire so I replaced it with one from the junk yard.....the reason it broke in the first place is because i was trying to get the thing behind the crank pulley off and my dad was hitting it with a hammer and bent it so when the crank spun it would break the sensor.....so when I changed the sensor and the car didnt start I was stumped and a little adjitated lol so I let the car sit for a day or two came back to it and decided to check the sensor again and thats when i realized the bent peice..and went to the junkyard piced up another sensor and balancer thing and she fired right up!!! the car was down a total of 2 weeks well I think it took that long because i had another car to drive if i was out a car then I would think it wouldve been fixed sooner lol Id hope.........sorry for such a long as reply haha
 
You must log in or register to reply here.

Similar threads

B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
737
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
318
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
Hard to start when engine is cold
  • 86_Capri
  • Mar 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
L
1997 V6 Starting issue
  • leanzik04
  • Mar 20, 2026
  • SN95 V6 Mustang Tech
Replies
3
Views
252
SN95 V6 Mustang Tech Mar 20, 2026
Noobz347
J
Car won’t start
  • JLB
  • Nov 15, 2025
  • SN95 4.6L Mustang Tech
Replies
4
Views
262
SN95 4.6L Mustang Tech Nov 15, 2025
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2.3L (N/A & Turbo) Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?