Car won't start, need some help.

FrumRoll

New Member
Mar 19, 2006
38
0
0
Took the car through the carwash today. Well it stalled while I was still in it, this isn't to unusual as it happens from time to time while at idle in gear. Started it back up and made it roughly three blocks when it stalled at roughly 30mph under load. I have never had this happen before. Figured there might be some moisture in the distributor, so I pulled the cap but no luck completely dry. I checked for spark by pulling a boot and grounding with a screwdriver, it tested positive for spark. I didn't have a gauge but I pushed the pin on the schroeder valve and I seem to have adequate fuel pressure. I have since changed the fuel filter and swapped TFI modules, plus batteries all with no luck. I'm at a bit of a loss now, the engine turns over with ease but refuses to fire. I'm hoping someone can help me. Also does anyone know how that killswitch in the hatch works, when I go to start the car the pump does prime so I'm assuming this isn't the issue but like I said I'm not real certain how it works. Also of note is that on attempted startup there is a single click from the general area of the ECU, I haven't had time to pinpoint it and I honestly can't say whether it always did this or not but I thought it should be noted. If any of you have any ideas that could help me please share. Thanks in advance.
 
Cranks OK, but No Start Checklist for Fuel Injected Mustangs

1.) Remove push on connector from starter solenoid and turn ignition switch on. Place car in neutral or Park. Remove coil wire from distributor & and hold 3/8” away from engine block. Jumper the screw to the big bolt on the starter solenoid that has the battery wire connected to it. You should get a nice fat blue spark.
Most of the items are electrical in nature, so a test light, or even better, a voltmeter, is helpful to be sure they have power to them.
No spark, possible failed items in order of their probability:
A.) MSD or Crane ignition box if so equipped
B.) Coil
C.) TFI module
D.) PIP sensor in distributor
E.) ECC relay next to computer - look for 12 volts at the fuel injector red wires
F.) Fuse links in wiring harness - look for 12 volts at the fuel injector red wires. All the fuse links live in a bundle up near the starter solenoid.
G.) Ignition switch - look for 12 volts at the ignition coil red/lt green wire.
H.) Computer

See the following links for wiring diagrams...

http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp for 79-88 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp for 89-93 model cars

http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-98 model cars


2.) Spark at coil wire, pull #1 plug wire off at the spark plug and check to see spark. No spark, possible failed items in order of their probability:
A.) Moisture inside distributor – remove cap, dry off & spray with WD40
B.) Distributor cap
C.) Rotor
D.) Spark Plug wires
E.) Coil weak or intermittent - you should see 3/8" fat blue spark with a good coil

3.) Spark at spark plug, but no start.
Next, get a can of starting fluid (ether) from your local auto parts store: costs a $1.30 or so. Then pull the air duct off at the throttle body elbow, open the throttle, and spray the ether in it. Reconnect the air duct and try to start the car. Do not try to start the car without reconnecting the air duct.
Two reasons:
1.) If it backfires, the chance for a serious fire is increased.
2.) On Mass Air cars, the computer needs to measure the MAF flow once the engine starts.
If it starts then, you have a fuel management issue. Continue the checklist with emphasis of fuel related items that follow. If it doesn’t, then it is a computer or timing issue: see Step 4.

Clue – listen for the fuel pump to prime when you first turn the ignition switch on. It should run for 5-20 seconds and shut off. To trick the fuel pump into running, find the ECC test connector and jump the connector in the lower RH corner to ground. See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html for a description of the test connector. If the relay & inertia switch are OK, you will have power to the pump. Check fuel pressure – remove the cap from the schrader valve behind the alternator and depress the core. Fuel should squirt out, catch it in a rag. Beware of fire hazard when you do this. In pinch you can use a tire pressure gauge to measure the fuel pressure. It may not be completely accurate, but you will have some clue as to how much pressure you have.

No fuel pressure, possible failed items in order of their probability:
A.) Tripped inertia switch – Coupe & hatch cars hide it under the plastic trim covering the driver's side taillight. Use the voltmeter or test light to make sure you have power to both sides of the switch
B.) Fuel pump power relay – located under the driver’s seat in most stangs built before 92. On 92 and later model cars it is located below the Mass Air Flow meter. Look for 12 volts at the Pink/Black wire on the fuel pump relay.
C.) Clogged fuel filter
D.) Failed fuel pump
E.) Blown fuse link in wiring harness. Look for 12 volts at the Orange/Lt Blue wire on the fuel pump relay. The fuse links live in the wiring harness near the starter solenoid.
F.) Fuel pressure regulator failed. Remove vacuum line from regulator and inspect for fuel escaping while pump is running.

Fuel pressure OK, the injectors are not firing.

A.) A Noid light available from Autozone, is one way to test the injector wiring.
B.) I like to use an old injector with compressed air applied to the injector where the fuel rail would normally connect. I hook the whole thing up, apply compressed air to the injector and stick it in a paper cup of soapy water. When the engine cranks with the ignition switch on, if the injector fires, it makes bubbles. Cheap if you have the stuff laying around, and works good too.

a.) Pull an injector wire connector off and look for 12 volts on the red wire when the ignition switch is on.
b.) No power, then look for problems with the 10 pin connecter (salt & pepper shakers at the rear of the upper manifold).
c.) No power and the 10 pin connections are good: look for broken wiring between the orange/black wire on the ECC relay and the red wire for the 10 pin connectors.


4.) Spark & fuel pressure OK.

A.) Failed IAB (no airflow to start engine). Press the throttle ¼ way down and try to start the car.
B.) Failed computer (not very likely)
C.) Engine ignition or cam timing off: only likely if the engine has been worked on recently).
D.) Firing order off: HO & 351 use a different firing order from the non HO engines.
HO & 351W 1-3-7-2-6-5-4-8
Non HO 1-5-4-2-6-3-7-8
E.) No start when hot - Press the throttle to the floor & try starting it if you get this far. If it starts, replace the ECT.
 
Just an update, I sprayed some starting fluid(Ether) into the intake manifold and was still unable to get it to fire. I took a look at the gray and white harnesses near the rear of the intake, and I found a wire that seemed to have melted or shorted I also fixed that and still no luck. According to your sheet I should be at step 4, well no amount of throttle modulation gets the car to run, neither ignition or cam timing have been screwed with. The firing order is certainly correct and the car doesn't start when it's hot or cold. How very unlikely is it to be the computer, and could the carwash be related. I'd hate to blow a computer each time I go through the carwash.
 
FrumRoll said:
Just an update, I sprayed some starting fluid(Ether) into the intake manifold and was still unable to get it to fire. I took a look at the gray and white harnesses near the rear of the intake, and I found a wire that seemed to have melted or shorted I also fixed that and still no luck. According to your sheet I should be at step 4, well no amount of throttle modulation gets the car to run, neither ignition or cam timing have been screwed with. The firing order is certainly correct and the car doesn't start when it's hot or cold. How very unlikely is it to be the computer, and could the carwash be related. I'd hate to blow a computer each time I go through the carwash.
The coil is suspect at this time. Mine died while driving down the interstate, and I coasted down a off ramp and into a parking lot. I have seen coils spark, but they didn't have a nice fat blue spark, and the car would not start.
 
Well I replaced the coil, took one off of my buddies '89 with no change, installed my coil in his car and it fired up instantly. So we switched it back and that's how it sits for now. This time out I noticed that while it's cranking(but not starting obviously), the fuel gauge goes up. It shows half a tank, and rose to 3/4 before I stopped cranking. At which point it fell back to half. It gave the impression that it would've risen all the way to full if I had cranked it over long enough. Not sure what that means if anything.