• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Changing rear springs...

  • Thread starter Thread starter 3024bblHO
  • Start date Start date Aug 6, 2006
3

3024bblHO

New Member
Jul 29, 2006
28
0
0
Aug 6, 2006
#1
  • Aug 6, 2006
  • #1
Hi guys, i am going to change the rear springs out on my 85 Mustang GT coupe because the rear end is sagging. I am going to go with basic springs, not trying to lower the car. My question is, how hard are rear springs to install on this car? What all goes into it? Thanks
 

NOSNotch

Founding Member
Oct 20, 2001
577
0
0
South Jersey
Aug 6, 2006
#2
  • Aug 6, 2006
  • #2
not bad at all if you have some mechanical ability. undo the upper shock nuts with a jack under the center of the rear. if you lower the jack you should be able to get the springs out otherwise you might have to undo the bolt for the lower control arm.
 
I

iwashmycar

20+ Year Stangneter
Apr 7, 2004
1,236
1
39
Columbus, Ohio
Aug 6, 2006
#3
  • Aug 6, 2006
  • #3
undo the shocks and the quads, with a jack under the rear end. You can only lower it soo far before there will be a peice of brake line that is ready to snap. From here i used another jack to jack up the side of the axle, thus making the alternate side drop even lower, where the spring will basically fall out with a little pry....new spring in....jack up the other side....button up the shocks and quads and your done.


-adam
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Aug 6, 2006
#4
  • Aug 6, 2006
  • #4
Very easy ... take off the lower shock bolts (so the shocks are no longer attached to the axle) and then unbolt the sway bar (at a minimum loosen it a good amount) then drop the rear down as low as it will go without straining the soft brake line on top of the rear. After that the tension will be pretty much released from the spring and you can just pull down on the rear depending on what side you are trying to remove. Just reverse to install. Very simple, just did it today

EDIT: Thanks IWASH - if you have quads pull the bolt out that attaches to the axle.
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Aug 7, 2006
#5
  • Aug 7, 2006
  • #5
I just remove the shock/quad shock, let it hang fully, and stand on the brake drum, then grab the spring out.
 
You must log in or register to reply here.

Similar threads

S
Brakes 80 Mustang 4.2 rear chassis brake line for 5 lug conversion!
  • StangPowerLSX510
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
191
Fox 5.0 Mustang Tech Aug 9, 2026
limp
Suspension Is somethig Wrong Here?
  • Icemanxxxv
  • Jul 11, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
230
Fox 5.0 Mustang Tech Jul 11, 2026
AeroCoupe
Front Coil Overs and Rear Traditional Springs within a Maximum Motorsports K-Member Kit
  • Habu135
  • Sep 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
24
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 9, 2026
Habu135
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
313
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
C
Suspension Rear suspension help
  • Clark302
  • Aug 17, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
462
Fox 5.0 Mustang Tech Aug 17, 2025
Clark302
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?