• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Clutch Cable Fixed, However....

  • Thread starter Thread starter 865.0
  • Start date Start date Mar 5, 2006
8

865.0

New Member
Feb 23, 2006
24
0
0
Mar 5, 2006
#1
  • Mar 5, 2006
  • #1
Hey Gang,

Thanks for all the advice.

I ended up purchasing a new quadrant, cable, and adjuster from Maximum Motorsports.

Wow!..What a difference. Light years ahead of my BBK quardrant and aftermarket adjustable cable. Sorry Steeda, as I have mentioned that I was using your products, when in fact, it was a BBK unit. That's what happens over a seven year lapse.

Anyhow, clutch pedal effort has been reduced dramatically, but now have a rattling sound when I engage the clutch.

Any suggestions.

Thanks in advance
 

timewarped1972

Member
Jun 17, 2004
642
0
16
mesa, az
Mar 5, 2006
#2
  • Mar 5, 2006
  • #2
if it does it after you let up off the clutch pedal it's probably the throw out bearing. you may need to tighten that fwa another turn or so to put some light pre load on the bearing to kep it from rattling....
 
8

865.0

New Member
Feb 23, 2006
24
0
0
Mar 5, 2006
#3
  • Mar 5, 2006
  • #3
The clutch is silent except when you depress the pedal. It's not very loud but noticeable.
 

vikingpower

New Member
Dec 6, 2004
656
0
0
CWU Ellensburg, WA
Mar 5, 2006
#4
  • Mar 5, 2006
  • #4
I cant wait to ditch my BBK cable and put in a Maximum Motorsports one this week. Mine's so bad I'd almost rather walk!
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 5, 2006
#5
  • Mar 5, 2006
  • #5
I would still look at the TOB or a chewed bearing retainer.

Good luck.
 
8

865.0

New Member
Feb 23, 2006
24
0
0
Mar 6, 2006
#6
  • Mar 6, 2006
  • #6
HISSIN50, I will give it a look over.

What kind of problems should I expect with a bad TOB?

The car shifts nicely, it's just that little rattle when I depress the clutch. The Maximum tech guys told me to make sure I had the clutch adjusted properly. I gave it another go around this evening, and I can't get no better. If I loosen it, it grabs at the floor, and I don't want to over tighten it (FWA).

VIKING...All I can say is that the MMS combo is great. I have noticed that my cable alignment was off with the BBK unit, causing excessive wear on the cable at the bottom of the quadrant. I drove it like that for six years before the OEM cable let loose and another six months for the aftermarket adjustable cable. It may have been the alignment and not the quadrant, that was at fault. Giving BBK the Benefit of the Doubt.

Thanks for all the help
 

vikingpower

New Member
Dec 6, 2004
656
0
0
CWU Ellensburg, WA
Mar 6, 2006
#7
  • Mar 6, 2006
  • #7
865.0 said:
HISSIN50, I will give it a look over.

What kind of problems should I expect with a bad TOB?

The car shifts nicely, it's just that little rattle when I depress the clutch. The Maximum tech guys told me to make sure I had the clutch adjusted properly. I gave it another go around this evening, and I can't get no better. If I loosen it, it grabs at the floor, and I don't want to over tighten it (FWA).

VIKING...All I can say is that the MMS combo is great. I have noticed that my cable alignment was off with the BBK unit, causing excessive wear on the cable at the bottom of the quadrant. I drove it like that for six years before the OEM cable let loose and another six months for the aftermarket adjustable cable. It may have been the alignment and not the quadrant, that was at fault. Giving BBK the Benefit of the Doubt.

Thanks for all the help
Click to expand...

Yeah I first heard about the MM cable from HISSIN50 (thanks man) and I'll be installing mine this weekend... thank the gods!... I also have the same problem with the BBK alignment, when I put the second BBK cable in I noticed the cable had been rubbing the inside of the FW aduster. So I looked inside the hole in the firewall and sure enough the top of the quadrant is above the top of the hole, so the bending is what I imagined caused the cable to break. Bottom line, I aint buying anymore BBK stuff! Which is unfortunate because I've got other stuff from them that works perfectly... but I dont buy stuff from companies (anymore) that dont make quality products ALL the time.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 6, 2006
#8
  • Mar 6, 2006
  • #8
The TOB can eventually come apart or seize. When they are (or arent - they are an issue like RMS's) properly adjusted via the cable, they can prematurely wear. WHen a load is placed on them, they make noise (which can be different from the noise they make when there is slack in the cable, as they are wobbling around on the TOB loose during that dynamic).

A chewed bearing retainer can allow what was a good TOB to make some noise - that was why I said what I did. One or the other of the two is likely (obviously should you find occasion to be in that far, renewing each for their relative little cost, is wise. Use a Steel retainer rather than aluminum).

Good luck.
 
I

Irrational

New Member
Jan 30, 2004
26
0
0
Neptune NJ
Mar 26, 2006
#9
  • Mar 26, 2006
  • #9
I just did my clutch and adj cable. I hear what seems to be the throw out bearing when the cable is slack (pedal not deppressed). Really sucks I am guessing it is my retainer. I hate this
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 26, 2006
#10
  • Mar 26, 2006
  • #10
Irrational said:
I just did my clutch and adj cable. I hear what seems to be the throw out bearing when the cable is slack (pedal not deppressed). Really sucks I am guessing it is my retainer. I hate this
Click to expand...
A cable operated clutch should have some slight cable-preload at all times. If you dont have preload and hear noise, it might not be the fault of the TOB or bearing retainer, but simply the noise of the TOB being allowed to slop around on the retainer.

Good luck.
 

SPEEDYLIFSAVR

Founding Member
Sep 18, 2000
666
0
16
FL,89 LX 5.0
Mar 26, 2006
#11
  • Mar 26, 2006
  • #11
I second HISSIN50 , dont be afraid to tighten up that cable so your TOB is snug up against the fingers on your pressure plate .
 
You must log in or register to reply here.

Similar threads

Drivetrain Time to pull and lube the clutch cable
  • LX Dave
  • Dec 21, 2024
  • Fox 5.0 Mustang Tech
  • 2
Replies
30
Views
2K
Fox 5.0 Mustang Tech Jan 7, 2025
limp
C
1992 5.0 Clutch Cable Adjustment
  • Chrispy62
  • Aug 28, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
316
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 28, 2024
Chrispy62
C
A
SOLD For Sale: 1993 Ford Mustang Cobra Modified
  • anjteal93
  • Sep 5, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
13
Views
2K
Fox Body Mustangs For Sale (1979-93) Oct 26, 2025
Mindseye007
C
SOLD 1994-2004 Maximum Motorsports clutch height adjuster
  • Cobra Jet NJ
  • Mar 3, 2024
  • Drivetrain Parts
Replies
1
Views
691
Drivetrain Parts Sep 30, 2024
Cobra Jet NJ
C
V
Drivetrain Clutch Cable too Short?!
  • vpap1
  • May 9, 2023
  • Fox 5.0 Mustang Tech
Replies
9
Views
3K
Fox 5.0 Mustang Tech May 23, 2023
vpap1
V
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?