Clutch On Tricked Out 1970

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Mar 23, 2014

#1

• Mar 23, 2014

• #1

Ok -- As you may remember I have a Big tricked out 347 stroker in my car, elctronic ignition, extra election gas "pump" in the back and many other options.

The clutch is fried. It looks like they used a smalled one in the bell housing based on the holes.

Which ones should I consider? Will I need or should I consider a new fly wheel too?

Thanks!

 

horse sence

15 Year Member

Nov 29, 1999

12,247

8,094

233

Wile Coyote's stunt double

Mar 24, 2014

#2

• Mar 24, 2014

• #2

I had a bunch of Ford 302 boss pressure plates and metallic disks ,down to my last one . These things were so smooth ,no chatter. My last one is going in my 69.
I have never had good luck with any after market , They just don't work the same .

 

rbohm

Founding Member

Apr 12, 2002

6,698

550

204

tucson,az

Mar 24, 2014

#3

• Mar 24, 2014

• #3

i made some assumptions on what you are needing, but look at these, and change the search parameters as needed;

http://www.summitracing.com/search/...n?SortBy=BestKeywordMatch&SortOrder=Ascending

note that these are kits, which means they contain a fair number of parts, you can narrow or expand your parameters.

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Mar 24, 2014

#4

• Mar 24, 2014

• #4

I am checking it out ...

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Apr 10, 2014

#5

• Apr 10, 2014

• #5

Any other thoughts on a clutch?

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Apr 10, 2014

#6

• Apr 10, 2014

• #6

How about a Zoom HP series with kevlar?

 

R

racerxmd

Member

Jun 18, 2013

84

15

19

Maryland

Apr 10, 2014

#7

• Apr 10, 2014

• #7

I had a Zoom on my 347. It is a good clutch. You probably need one that is 10 1/2". What power level are you looking for? Is this a street,strip or both car? What is the manufacture of the one you removed or part #?

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Apr 10, 2014

#8

• Apr 10, 2014

• #8

Have not taken it out yet.it is a street i drive very hard. So like a half and half i guess

 

R

racerxmd

Member

Jun 18, 2013

84

15

19

Maryland

Apr 10, 2014

#9

• Apr 10, 2014

• #9

What are hp or power level you guess your motor put out?

 

iskwezm

10 Year Member

May 24, 2005

4,159

20

79

Rowland Heights,California

Apr 11, 2014

#10

• Apr 11, 2014

• #10

I used a Centerforce DF diaphragm clutch and hated it. It chattered from day one. I took it to Mcleod and they tested it and couldn't find any issues and they really didn't want to sell me one without knowing why it chattered. Well I bought one anyway and no more chattering. It lasted for many about 16 years till I started putting over 600 hp through it. They are nice enough to rebuild what I have and put a better disc for less then a new clutch.

 

ColinMAC

Member

Apr 2, 2014

58

5

9

Fountain, Colorado

Apr 11, 2014

#11

• Apr 11, 2014

• #11

i use modern drivelines organic/kevlar clutches. albeit they are for racing and high horsepower applications. i have one on mine, and if you dont get stupid dropping the clutch, itll last a long time. they sell the clutch kits, with either just the disk, or the pressure plate, disk, throwout bearing, and pilot bearing. they also sell flywheels, cast and lightened billet.
http://www.moderndriveline.com/catalog/clutches.htm

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Apr 14, 2014

#12

• Apr 14, 2014

• #12

We are guessing it is easily in the low 500 hp range

 

ColinMAC

Member

Apr 2, 2014

58

5

9

Fountain, Colorado

Apr 14, 2014

#13

• Apr 14, 2014

• #13

their kevlar/organic ones take that easily, full kevlar will take a lot more. organic is stock, kev/org is designed for extra grab and high heat tolerance from high performance applications. the Kevlar/Kevlar are made for long life and minimal wear with high performance, high torque applications. both will take it easily, its all up to you in he end.

 

Golden 68

Member

Dec 27, 2013

84

3

9

Hawley, Minnesota

Apr 15, 2014

#14

• Apr 15, 2014

• #14

Thanks ... but tough to decide on.

 

ColinMAC

Member

Apr 2, 2014

58

5

9

Fountain, Colorado

Apr 15, 2014

#15

• Apr 15, 2014

• #15

if you look at purely kevlar clutches, just make sure you check the fine print for kevlar content. many dont have 90+% kevlar content that modern drivelines claims to. Good luck!