• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

clutch popping

  • Thread starter Thread starter 91 HATCH
  • Start date Start date Oct 4, 2007

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Oct 4, 2007
#1
  • Oct 4, 2007
  • #1
what would make my clutch assembly pop when i press on the pedal
 

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Oct 4, 2007
#2
  • Oct 4, 2007
  • #2
Your clutch cable might be getting ready to snap. Mine started doing that a day or so before it got down to being a thread or two away from completely breaking. Pull it loose and give it a close look to see if you're at risk. If so, replace it immediately with a FORD "universal" cable from MM and, if you don't already have 'em, a FWA and aluminum quad.
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Oct 4, 2007
#3
  • Oct 4, 2007
  • #3
ok i will look at it thanks
 

5.0TailPipeHump

Member
Dec 5, 2006
153
0
17
Oct 5, 2007
#4
  • Oct 5, 2007
  • #4
I have the same problem , but it was not the cable , i went under the car and had a friend push down on the clutch and the poping sound was comming from the clutch fork when just about compressed @ all the way , my clutch works fine but it does get kinda annoying , somtimes it will pop and other times it wont . Check your fork out, when i replace the clutch this is when ill check my fork.
 

68keyblr

20+ Year Stangneter
Mar 17, 2003
946
20
49
Arizona
Oct 5, 2007
#5
  • Oct 5, 2007
  • #5
5.0TailPipeHump said:
I have the same problem , but it was not the cable , i went under the car and had a friend push down on the clutch and the poping sound was comming from the clutch fork when just about compressed @ all the way , my clutch works fine but it does get kinda annoying , somtimes it will pop and other times it wont . Check your fork out, when i replace the clutch this is when ill check my fork.
Click to expand...


I'd take a look at the throwout bearing riding along the shaft. Sounds like the throwout bearing might be binding.
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Oct 5, 2007
#6
  • Oct 5, 2007
  • #6
68keyblr said:
I'd take a look at the throwout bearing riding along the shaft. Sounds like the throwout bearing might be binding.
Click to expand...


I have a new dual friction setup with the steel bearing retainer and the cable is fine
 
F

Fox8950

Member
Jun 29, 2007
247
2
18
Oct 5, 2007
#7
  • Oct 5, 2007
  • #7
Definitely your quadrant than if you still have the stock plastic one .. especially once you put an aftermarket clutch in that has a little more pressure than stock that plastic thing snaps fast.
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Oct 5, 2007
#8
  • Oct 5, 2007
  • #8
i still have the plastic quadrant what is the best one to get and should i buy a firewall adjuster
 

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Oct 5, 2007
#9
  • Oct 5, 2007
  • #9
Yes, definitely invest in an aftermarket quad and FWA. With any non-adjustable cable, you'll NEED a firewall adjuster to take up the slack in lieu of having the stock plastic self-adjusting quadrant. Some places sell both together as a package combo deal for a few bucks cheaper than buying them separately (UPR and MM are two good sources).
 

5.0TailPipeHump

Member
Dec 5, 2006
153
0
17
Oct 5, 2007
#10
  • Oct 5, 2007
  • #10
91 HATCH said:
I have a new dual friction setup with the steel bearing retainer and the cable is fine
Click to expand...

Funny you say that , right after i had my steal bearing retainer replaced shortly after i had the popping noise aswell. 68keyblr might be right. Would the fork have anything to do with popping?
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Oct 5, 2007
#11
  • Oct 5, 2007
  • #11
get your quadrant fixed any is better than that plastic one
 

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Oct 5, 2007
#12
  • Oct 5, 2007
  • #12
I guess I'm not seeing where/how the clutch fork could make a popping sound or feeling. It's just an arm on a ball pivot. If the ball pivot isn't lubed, it might squeak or something, but that's about all. If the throwout bearing isn't installed correctly upon the clutch fork (without both prongs going under it), then it'd probably howl and squeal and raise hell, but it wouldn't "pop."

If the throwout bearing is getting hung up on a ridge or snag on the input shaft bearing retainer (possibly not lubed enough/properly, or serious wear marks from prior bearing failure?), then that might make the pedal operate less smoothy and feel like it has a "hitch" to it ... but still not likely to result in a definite "popping" kinda sensation or sound.

The plastic quad sounds more suspect to me. Old rusty springs and brittle plastic can make all kinds of crunchy, weird noises and stuff, especially when they start rotting out enough that they're falling apart.

Again, I'd recommend swapping 'em for an aluminum quad and FWA. Even if it isn't the full cause of the problem, it's definitely a worthwhile upgrade, and likely to prevent a future situation of getting stuck in the middle of traffic with a busted quadrant (or, worse still, premature clutch wear from improper self-adjustment).
 

91 HATCH

Banned
May 17, 2007
262
0
0
illinois
Oct 5, 2007
#13
  • Oct 5, 2007
  • #13
i am buying the quad and adjuster now thanks
 
You must log in or register to reply here.

Similar threads

4
Drivetrain Wilwood Clutch and Brake Pedal Combo Installation - Help
  • 427stang
  • Jul 8, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
127
Fox 5.0 Mustang Tech Jul 8, 2026
427stang
4
WTB Wanted - Foxbody clutch pedal
  • TTSaleen
  • Aug 4, 2026
  • Want to Buy
Replies
3
Views
204
Want to Buy Aug 6, 2026
General karthief
D
Mustang not starting
  • Dawry Ramos
  • Sep 12, 2026
  • 2015 - 2023 Specific Tech
Replies
10
Views
415
2015 - 2023 Specific Tech Oct 3, 2026
Dawry Ramos
D
Clutch pedal to Quadrant lag
  • Potomus Pete
  • Aug 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
412
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
Noobz347
F
Engine 1988 Foxbody idle issues
  • fernandosgarage55
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
26
Views
1K
Fox 5.0 Mustang Tech Apr 30, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?