• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

control arms came loose!!

  • Thread starter Thread starter vtecwho
  • Start date Start date Sep 26, 2008

vtecwho

New Member
Feb 24, 2008
61
0
0
Sep 26, 2008
#1
  • Sep 26, 2008
  • #1
its not as bad as you think. the rear end did not fall off or anything but i did think that this was a big enough deal to warn others about.

for no reason i double checked my bolts that hold my lakewood control arms on, both upper and lower, and most were very loose!

the car, i noticed, was very sloppy around corners and such.

after tighting them up i noticed right away that the rear end did not move side to side NEAR as much as it did before.

it only took me time to change shirts, get a jack, and a 3/4 inch socket and driver to do this, SO GO AND CHECK.

i would hate to imagine what would have happened it on came off while on the highway

it was never anything that i thought i would have to check again but its kinda a big deal if they were to fail, so, i just thought i would share some "useful" info with you all

Eric
 

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
Sep 27, 2008
#2
  • Sep 27, 2008
  • #2
Well on my control arms the nut side has is a self locking nut. Been on there for 5 years and never gotten loose. Maybe you should try some loctite on them.
 

capri debris

Member
May 5, 2007
289
6
18
PA
Sep 28, 2008
#3
  • Sep 28, 2008
  • #3
The recommended torque for those bolts is 190 ft/lb. Most people who replace their control arms just get a breaker bar and give it hell and think they are tight enough... WRONG. That's probably all you did after you found out they were loose. I suggest you go back out to your car, with torque wrench this time, and you're gonna crap at how much MORE you have to tighten them to achieve 190 ft/lbs. And BTW, it pretty tough to do by yourself. You need someone to hold the bolt for you with a breaker bar and a socket while you use BOTH hands on the torque wrench to tighten the nut.
 
You must log in or register to reply here.

Similar threads

A
SN95 Multifunction Madness! Need some big brain assistance from you folks
  • Awnaw
  • Oct 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
131
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Tuesday at 5:36 PM
AeroCoupe
Considering widening my rear wheels, would like to verify my thoughts on fitment
  • 2000xp8
  • Jul 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
37
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 18, 2026
AeroCoupe
Tightening upper control arm bushings at ride height dilemma… need some help
  • AnthonyA1234
  • Dec 27, 2024
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
51
Views
7K
Fox 5.0 Mustang Tech Feb 27, 2025
General karthief
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
506
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
L
95 gt engine vibration
  • lenzgt
  • May 11, 2026
  • 1994 - 1995 Specific Tech
Replies
6
Views
379
1994 - 1995 Specific Tech May 26, 2026
lenzgt
L
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?