• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

crush sleeve

  • Thread starter Thread starter 1991vert
  • Start date Start date Aug 1, 2007

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 1, 2007
#1
  • Aug 1, 2007
  • #1
last season i put in new axles and a differential and took everything out of the 8.8 housing. i dont think i tightened the crush sleeve enough and was wondering if i needed a whole new crush sleeve or could i just tighten this one some more?

i know you can never loosen them once you tighten them, but what about tightening more?
 
R

red95gtconvert

New Member
May 29, 2006
382
0
0
Ponca city, OK
Aug 1, 2007
#2
  • Aug 1, 2007
  • #2
You can continue to tighten it but don't overtighten it and exceed the recommended bearing preload or the pinion bearings won't last very long.
 
D

dtlionsfan

Member
Nov 12, 2005
83
0
16
Aug 1, 2007
#3
  • Aug 1, 2007
  • #3
I've done many pinion seals over the years by torqueing the pinion nut to 150 pds. ft. with red locktite.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 2, 2007
#4
  • Aug 2, 2007
  • #4
so would 150ft/lbs torque be good?
 

Goober89

New Member
Jul 30, 2007
8
0
2
Palm Bay, FL
Aug 2, 2007
#5
  • Aug 2, 2007
  • #5
you need to go by turning torque my friend. you need a special turning torque wrench and you are supposed to measure it with the axles out of it. why do you think you didnt tighten it enough?
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 2, 2007
#6
  • Aug 2, 2007
  • #6
Goober89 said:
you need to go by turning torque my friend. you need a special turning torque wrench and you are supposed to measure it with the axles out of it. why do you think you didnt tighten it enough?
Click to expand...

i know i need a beam style torque wrench which measure in in/lbs, but no one around here carries one. and ya i dont think i tightened it enough. i pulled out the rear end to weld the torque boxes and it was all gross up there - yes, it wasnt there before.
 
R

red95gtconvert

New Member
May 29, 2006
382
0
0
Ponca city, OK
Aug 2, 2007
#7
  • Aug 2, 2007
  • #7
Sounds like pinion seal failure to me.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 2, 2007
#8
  • Aug 2, 2007
  • #8
i was in a rush and never really correctly tightened it. i just torqued it down until i felt no play

so tightening to 150ft/lbs, like suggested above, would be a bad idea?
 

ronburgundy

Member
Nov 19, 2006
179
0
16
BC coast
Aug 2, 2007
#9
  • Aug 2, 2007
  • #9
impact gun always works for me. and a big old hammer. never lost one yet.
 
D

dtlionsfan

Member
Nov 12, 2005
83
0
16
Aug 2, 2007
#10
  • Aug 2, 2007
  • #10
For Gods sake don't use an impact gun.I've done this for 25 years and not as a hobby.150 pds. ft. Correct way is a beam torque wrench with carrier removed should have 20 inch pds new bearings and 15 inch pds used bearings.
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 3, 2007
#11
  • Aug 3, 2007
  • #11
dtlionsfan said:
For Gods sake don't use an impact gun.I've done this for 25 years and not as a hobby.150 pds. ft. Correct way is a beam torque wrench with carrier removed should have 20 inch pds new bearings and 15 inch pds used bearings.
Click to expand...

i know it's 10-15 in/lbs with a dial torque wrench, but i dont want to spend $150-$200 on something im going to use once. i wish autozone rented these things, but they'd probably get messed up faster than lindsay lohan at a party
 

1991vert

10 Year Member
Feb 27, 2004
1,103
7
69
Ludlow, MA
Aug 5, 2007
#12
  • Aug 5, 2007
  • #12
well i bought one and just for giggles checked what the current preload was and it didnt even register on the torque wrench. i pulled everything apart and replaced the pinion seal just in case and put a new crush sleeve in and now it should be fine. now im just waiting on my rear end girdle to put it back together
 
You must log in or register to reply here.

Similar threads

Clutch pedal to Quadrant lag
  • Potomus Pete
  • Aug 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
413
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
Noobz347
S
Cobra 8.8 differential rebuild shop question
  • Sestemybe
  • Aug 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
480
1996 - 2004 SN95 Mustang -General/Talk- Nov 15, 2025
baileygruwell
B
J
2004 Mustang 3.8L V6 vibrations above 65 MPH and differential leaks
  • joeybuddy96
  • Mar 16, 2026
  • SN95 V6 Mustang Tech
Replies
17
Views
1K
SN95 V6 Mustang Tech Aug 29, 2026
joeybuddy96
J
S
Drivetrain 8.8 Pinion and 302 rear main seal leaks after replacing. 93 5.0 with t-5
  • Steigy4827
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
892
Fox 5.0 Mustang Tech Apr 1, 2026
Steigy4827
S
Suspension 87 steering wheel slightly wobbles after new Rag joint install
  • R82148V
  • Jun 16, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
25
Views
1K
Fox 5.0 Mustang Tech Jun 24, 2025
R82148V
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?