edelbrock shocks won't fit on my 68

S-Car-Go

Member

Mar 25, 2003

332

0

16

San Jose, CA

Aug 25, 2005

#1

• Aug 25, 2005

• #1

Almost have the front end back together and I can't get the upper shock mount over the end of the shocks The body is too big to slide up from the bottom and there is no way to twist the end back and forth like you normally do. The shock mounts upside down from traditional. I'm starting to think you need to use a 65/6 shock mount to get a little more wiggle room on the top. Anyone else run into this? Ideas?

To add insult to injury I have an appointment for an alignment in 9 hrs

 

dodgestang

Active Member

Dec 15, 2003

1,360

0

37

Cecil County, MD

Aug 25, 2005

#2

• Aug 25, 2005

• #2

Well....I have IAS in the 65 and the shock tower cap mounts was not a problem. Have you considered simply opening up the cap a little bit more with a grinder?

 

2nd Mustang

Founding Member

Feb 24, 2002

2,488

0

46

Southern California

Aug 25, 2005

#3

• Aug 25, 2005

• #3

Do you mean that the top of the shock is too wide? I once had that problem on a Chebie and just ground down the end of the shock eyelet area.

 

S-Car-Go

Member

Mar 25, 2003

332

0

16

San Jose, CA

Aug 25, 2005

#4

• Aug 25, 2005

• #4

I thought about grinding the cap, but I'd have to remove a LOT of material. Looking at the cap, it looks a lot smaller (shorter)than a 65 cap, but the bolt pattern has to be the same because the springs are the same diamater.
2ndMustang, the AIS has the thin end pointing down so you have to slip the shock body onto the cap. Koni's, KYB, etc have the body mount to the spring perch and you slip the cap over the thin end with no problem.

 

R

Red5oh

Member

Jul 8, 2005

377

0

17

DFW, Texas

Aug 25, 2005

#5

• Aug 25, 2005

• #5

I have a 67 with the IAS shocks... I had to remove the shock tower cap, and slide the shock in. Then, remove the top shock mount pin, put the cap back on and slide the mount pin back in. A total PIA, but it works.

Let me know if you come up with anything different.

Mark

 

S-Car-Go

Member

Mar 25, 2003

332

0

16

San Jose, CA

Aug 25, 2005

#6

• Aug 25, 2005

• #6

Done.. PITA! Okay this post is for the next guy who's looking to put these in a 68 and doing a search.

Like Red50h said, you have to press (or beat) the upper cross-piece out of the bushing, slip the shock tower cap over the end, and press the cross-piece back in place. Mine came with black cross-pieces installed which didn't fit the bolt pattern on the cap. (guess when I discovered this.. ) There are two silver cross-pices in the packs of hardware that are shorter and line up with the holes in the cap. Lastly, the shock body rubs on the cap on all sides, so I'm not sure what good the upper bushing is going to do. The car is back on the ground but I haven't driven it yet. Can't wait for tomorrow.

 

iskwezm

10 Year Member

May 24, 2005

4,159

20

79

Rowland Heights,California

Aug 26, 2005

#7

• Aug 26, 2005

• #7

dodgestang said:

Well....I have IAS in the 65 and the shock tower cap mounts was not a problem. Have you considered simply opening up the cap a little bit more with a grinder?

Click to expand...

thats what i did on mine