• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

EEC test problems PLEASE HELP!!!

  • Thread starter Thread starter mr_tinkertrain
  • Start date Start date May 29, 2004
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 29, 2004
#1
  • May 29, 2004
  • #1
With the way my car runs, i decided to run the eec test with jumper wire and voltmeter. I hooked the jumper wire and everything up right turned the key and the voltmeter just pegged out and stayed there. It would not move. I started the car with the jumper wire still in place and the car revved up to about 1600 rpm and slowly idled back down like it was searching for its idle. I can unplug the jumper while car is running and sometimes it just dies. Doest sputter or anything it just dies. What is wrong with my car???? Is teh wiring messed up? I get NO codes from koer or koeo tests. It just pegs the voltmeter out and doesnt move it. Maybe i need to change the voltmeters settings? Help me out!
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
May 29, 2004
#2
  • May 29, 2004
  • #2
don't you just use the check engine light? I'm not positive, but I don't even think you need a voltmeter to pull codes, I think all you need is that jumper wire, but I could be wrong... If you do need the voltmeter, you just have it set wrong.
 
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 29, 2004
#3
  • May 29, 2004
  • #3
thats true but thanks to my dad (i know hes not too smart but this was before his son *me* informed him of all the details on a computer controlled vehicle) the check engine light was removed, painted black lol and reinstalled. So in order to use that method i'd have to take the light out and replace it. Problem with that is the plastic piece of the dash that has the headlight switch and stuff on it is broken where it mounts to the dash. It is siliconed on there to keep it from falling off (for now) and i dont really want to have to take it off right now and re silicone it. This car was beatin to death its whole life until now when i'm trying to make it new again. Daily driven for 13 years. 191,xxx miles. So check engine light test is out.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 29, 2004
#4
  • May 29, 2004
  • #4
Are you sure you have the voltmeter connected properly?

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.dalidesign.com/hbook/eectest.html for more descriptive help
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

have the voltmeter connected properly? follow these links for help>
 
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 29, 2004
#5
  • May 29, 2004
  • #5
if i touch the two ends of the voltmeter together the needle moves so i'm pretty sure its set correctly. I can change the settings but the needle still only moves so far then it just stays there. there is no movement of the needle.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 29, 2004
#6
  • May 29, 2004
  • #6
mr_tinkertrain said:
if i touch the two ends of the voltmeter together the needle moves so i'm pretty sure its set correctly. I can change the settings but the needle still only moves so far then it just stays there. there is no movement of the needle.
Click to expand...


Sounds like you are using the Ohms function. Ohms are for measuring resistance and checking fuses. Don't use Ohms to measure a powered up circuit or you risk damaging the meter.

Select the voltage function or follow the link in my previous post & use a test light.
 
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 29, 2004
#7
  • May 29, 2004
  • #7
Youre right i was using ohms but i switched to voltage with no change. It still does the same thing. Maybe i'm using the wrong plug. I KNOW i have the eec test plug but i'm not absolutely sure i have the correct small plug the jumper wire is supposed to be ran to. The plug i have has 2 wires running to it, not just one. So which side am i supposed to use? It is located in the driver side engine bay just behind the shock tower along with the EEC plug. Can someone get me a picture of the plugs?
 
5

5.0guy

Member
Apr 17, 2004
320
0
17
MI
May 29, 2004
#8
  • May 29, 2004
  • #8
 
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 30, 2004
#9
  • May 30, 2004
  • #9
thats how i've got it but still no luck!
 
5

5.0guy

Member
Apr 17, 2004
320
0
17
MI
May 30, 2004
#10
  • May 30, 2004
  • #10
take it to autozone or someplace like that...they should test it for free.
 
M

mr_tinkertrain

Member
Dec 14, 2003
151
0
16
Hot Springs, AR
May 31, 2004
#11
  • May 31, 2004
  • #11
used a test light with same outcome, the light continously stays on
 
R

rockin_rick

Member
Oct 9, 2003
968
1
17
Jun 17, 2004
#12
  • Jun 17, 2004
  • #12
Did you figure this out yet?

Rick
 
M

mattfleming

New Member
Mar 22, 2004
33
0
0
Dec 2, 2005
#13
  • Dec 2, 2005
  • #13
:bump: same problem.

Jumper from STI to the jumper slot, positive on positive terminal, negative on STO.,

I'm getting a constant 12 volts.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Dec 2, 2005
#14
  • Dec 2, 2005
  • #14
The probablity is that you have some wiring problems.

The black/white wire on the self test connector is signal ground for the
computer. With the ignition switch OFF, measure the resistance between the
black/white wire on the self test connector and ground. You should see less
than 1 ohm. More than 1 ohm means some bad connections. More that 1000
ohms is some broken wiring.

Diagram courtesy of Tmoss and Stang&2birds.



The next steps require you to remove the passenger side kick panel and then
remove the wiring connector from the computer. A 10 MM socket is needed
to get the computer connector off.

Mesure the resistance between the STI (pigtal connector and pin 48 on the
computer. With the ignition switch OFF, measure the resistance between the
white/red wire on the self test connector pigtail and and pin 48. You should
see less than 1 ohm. More than 1 ohm means some bad connections. More
that 1000 ohms is some broken wiring.

See the following website for some help from Tmoss (diagram designer) &
Stang&2Birds (website host) for help on 88-90 wiring

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif
 

Attachments

  • 88-91eecPinout.gif
    167.1 KB · Views: 127
You must log in or register to reply here.

Similar threads

Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
392
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
518
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
388
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
186
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
657
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?