• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

EGR / Charcoal Box?

  • Thread starter Thread starter TrickFlowd
  • Start date Start date Nov 5, 2007

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 5, 2007
#1
  • Nov 5, 2007
  • #1
Can I eliminate these two? The smog pump is already gone. I unplug the egr and it does nothing in how the car runs. Can I just block off the vacuum on the intake and build a plate to block off EGR?

Also, the charcoal box...can I just block off the lines? The kid I bought the car from took all the emissions stuff out, and left alot of stuff just sittin there but unhooked. Charcoal box only has one vacuum on it, other is open, egr was unhooked and vacuum was plugged off, smog pump is gone, and most other vacuum lines are unhooked as well. I plan to have who ever tunes the car eliminate the EGR and smog codes and burn a chip to be rid of this stuff...since I don't have to worry about inspection.
 

$uperstang

New Member
Jul 20, 2004
476
1
0
Detroit, MI
Nov 5, 2007
#2
  • Nov 5, 2007
  • #2
Yes get rid of all that crap. The line going to the EVAP canister vents the gas tank so just extend it to vent under the radiator that way it is up front and you get no gas smell, dont forget to cap the vauum port on the intake. Yes you can remove the EGR and make a plate to plug it. Also remove the EVP sensor behind the passenger shock tower, this is the sensor that tells the EGR when to open and close basically.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 5, 2007
#3
  • Nov 5, 2007
  • #3
It does not weigh but a pound or so and helps richen up the cruse mixture. It draws no HP & keeps the car from smelling like gasoline in a closed garage. So with all these good things and no bad ones, why not hook it up & use it?

Charcoal canister plumbing - one 3/8" tube from the bottom of the upper manifold to the rubber hose. Rubber hose connects to one side of the canister solenoid valve. Other side of the solenoid valve connects to one side of the canister. The other side of the canister connects to a rubber hose that connects to a line that goes all the way back to the gas tank. There is an electrical connector coming from the passenger side injector harness near #1 injector that plugs into the canister solenoid valve. It's purpose is to vent the gas tank. The solenoid valve opens at cruse to provide some extra fuel.
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 5, 2007
#4
  • Nov 5, 2007
  • #4
Can I relocate the charcoal box to somewhere else? It looks hideous without the smog pump blocking the view. Trying to clean up the engine bay a bit.

The EGR being gone, can they clean that out of my computer when tuning comes?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 5, 2007
#5
  • Nov 5, 2007
  • #5
Yes, if you delete the EGR, you need to tune it out when you get your car dyno tuned.
 

soontobefastfox

Member
Nov 15, 2005
275
0
16
Troy, Michigan
Nov 5, 2007
#6
  • Nov 5, 2007
  • #6
jrichker said:
It does not weigh but a pound or so and helps richen up the cruse mixture. It draws no HP & keeps the car from smelling like gasoline in a closed garage. So with all these good things and no bad ones, why not hook it up & use it?

Charcoal canister plumbing - one 3/8" tube from the bottom of the upper manifold to the rubber hose. Rubber hose connects to one side of the canister solenoid valve. Other side of the solenoid valve connects to one side of the canister. The other side of the canister connects to a rubber hose that connects to a line that goes all the way back to the gas tank. There is an electrical connector coming from the passenger side injector harness near #1 injector that plugs into the canister solenoid valve. It's purpose is to vent the gas tank. The solenoid valve opens at cruse to provide some extra fuel.
Click to expand...

+1 that is the exact reason(s) I decided to keep the EGR and Charcoal Canister.

But what you can do is delete the coolant lines that go to the EGR spacer (if you don't drive the stang in the winter, the coolant is for cold starts).
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 5, 2007
#7
  • Nov 5, 2007
  • #7
soontobefastfox;7194448(if you don't drive the stang in the winter said:
It's to cool down the hot EGR spacer. If the EGR is deleted, so can the lines.


It can't really help with cold starts because the coolant doesn't warm up til 10 minutes after the car has been started
Click to expand...
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 6, 2007
#8
  • Nov 6, 2007
  • #8
The charcoal box...do I just plug off the lines or run them to the front of the car and let it vent? My car smells like fuel anyways!

Mustang5L5- Your avatar is the SHIOT!!!
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 6, 2007
#9
  • Nov 6, 2007
  • #9
Let it vent, but route it in an area where vapors won't be trapped.

Remember, gasoline vapors are explosive in the right concentration level.


Oh and She is hot!
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 6, 2007
#10
  • Nov 6, 2007
  • #10
Down low in the front bumper so the fumes go out under the car? Can I just lengthen the line and relocate the charcoal box behind the bumper so its out of site? I don't really want my car to explode.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 6, 2007
#11
  • Nov 6, 2007
  • #11
TrickFlow'd said:
Down low in the front bumper so the fumes go out under the car? Can I just lengthen the line and relocate the charcoal box behind the bumper so its out of site? I don't really want my car to explode.
Click to expand...

That is the way to go. Inside the fender would work well also (this is where they put the cannister on 5N95's).

Good luck.
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 6, 2007
#12
  • Nov 6, 2007
  • #12
On the canister, there is a smaller line that comes from through the firewall, and there is a bigger line (mine is unhooked, the kid I bought the car from eliminated the smog pump and a/c) this line is not there. Where does the bigger line go? Or is that a vent? Just trying to figure out all the cob jobs that were performed on my car.

Thanks guys!
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 6, 2007
#13
  • Nov 6, 2007
  • #13
it's a vacuum like that runs up into the front of the intake manifold. It connects underneath on the front side.

Look for a vac line coming out..unless you have aftermarket intake.

Basically the vapors are brought into the engine and combusted after passing through activated charcoal
 
D

DREAMZOFHIRPM

New Member
Sep 25, 2007
40
0
0
BROOOOOOOKLYNN
Nov 6, 2007
#14
  • Nov 6, 2007
  • #14
I deleted all that stuff.. I actually found a tiny AND I MEAN EXTREMELY TINY FILTER THAT k&N MAKES AND I PUT IT AT THE END tHE FILTERE OF THE LINE.. IT DEFINITLY HELPED WITH THE GAS SMELL.. AND THEIR FILTERS ARE GOOD FOR LIFE,, I CLEAN IT WHEN I DO OIL CHANGES,,,THE FILTER IS ABOUT TWO THUMB WDITHS WIDE AND THE INLET IS AS SMALL AS THE VENT LINE.... WORKED GREAT
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 7, 2007
#15
  • Nov 7, 2007
  • #15
Mustang5L5 said:
it's a vacuum like that runs up into the front of the intake manifold. It connects underneath on the front side.

Look for a vac line coming out..unless you have aftermarket intake.

Basically the vapors are brought into the engine and combusted after passing through activated charcoal
Click to expand...

I'm running a Track Heat intake. Can just vent the vapors out the wheel well or something? Or would you recommend relocating the box so its hidden?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 7, 2007
#16
  • Nov 7, 2007
  • #16
Personally, i would relocate the box.


The other line just needs to see vacuum from the manifold. Do you have any spare vac ports on the manifold where you can run a vac line to from the canister.

I wouldn't vent it. You are venting gasoline vapors from your fuel tank. You don't want to take a chance and start an underhood fire. Just hide the box which weighs 2 pounds and route the vac line to the intake
 

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Nov 7, 2007
#17
  • Nov 7, 2007
  • #17
Yeah there are a few on the underside. There is one tiny line coming from the Firewall, and a bigger one that is unhooked and thats the one I run to the manifold. That sounds like a plan. Thanks man!
 
You must log in or register to reply here.

Similar threads

R
Engine Evap and charcoal cannister leak
  • ryan1994stang
  • Mar 14, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
660
Fox 5.0 Mustang Tech Mar 18, 2026
Mcmahst
D
Please help with vacuum lines
  • Dawgs000082
  • May 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
248
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 10, 2026
Dawgs000082
D
S
Fuel ‘88 GT Runs Rich Cold — Fixes Itself When I Unplug Sensors (ECT, MAF, O2, etc.)
  • Sufarry
  • Nov 6, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
1K
Fox 5.0 Mustang Tech Nov 9, 2025
Mustang5L5
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
J
Emission problems
  • jls.zmmr
  • Feb 5, 2026
  • 1994 - 1995 Specific Tech
Replies
2
Views
343
1994 - 1995 Specific Tech Feb 7, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?