EGR / Charcoal Box?

TrickFlowd

Member
May 17, 2003
240
0
16
Sayre, PA
Can I eliminate these two? The smog pump is already gone. I unplug the egr and it does nothing in how the car runs. Can I just block off the vacuum on the intake and build a plate to block off EGR?

Also, the charcoal box...can I just block off the lines? The kid I bought the car from took all the emissions stuff out, and left alot of stuff just sittin there but unhooked. Charcoal box only has one vacuum on it, other is open, egr was unhooked and vacuum was plugged off, smog pump is gone, and most other vacuum lines are unhooked as well. I plan to have who ever tunes the car eliminate the EGR and smog codes and burn a chip to be rid of this stuff...since I don't have to worry about inspection.
 
Yes get rid of all that crap. The line going to the EVAP canister vents the gas tank so just extend it to vent under the radiator that way it is up front and you get no gas smell, dont forget to cap the vauum port on the intake. Yes you can remove the EGR and make a plate to plug it. Also remove the EVP sensor behind the passenger shock tower, this is the sensor that tells the EGR when to open and close basically.
 
It does not weigh but a pound or so and helps richen up the cruse mixture. It draws no HP & keeps the car from smelling like gasoline in a closed garage. So with all these good things and no bad ones, why not hook it up & use it?

Charcoal canister plumbing - one 3/8" tube from the bottom of the upper manifold to the rubber hose. Rubber hose connects to one side of the canister solenoid valve. Other side of the solenoid valve connects to one side of the canister. The other side of the canister connects to a rubber hose that connects to a line that goes all the way back to the gas tank. There is an electrical connector coming from the passenger side injector harness near #1 injector that plugs into the canister solenoid valve. It's purpose is to vent the gas tank. The solenoid valve opens at cruse to provide some extra fuel.
 
Can I relocate the charcoal box to somewhere else? It looks hideous without the smog pump blocking the view. Trying to clean up the engine bay a bit.

The EGR being gone, can they clean that out of my computer when tuning comes?
 
It does not weigh but a pound or so and helps richen up the cruse mixture. It draws no HP & keeps the car from smelling like gasoline in a closed garage. So with all these good things and no bad ones, why not hook it up & use it?

Charcoal canister plumbing - one 3/8" tube from the bottom of the upper manifold to the rubber hose. Rubber hose connects to one side of the canister solenoid valve. Other side of the solenoid valve connects to one side of the canister. The other side of the canister connects to a rubber hose that connects to a line that goes all the way back to the gas tank. There is an electrical connector coming from the passenger side injector harness near #1 injector that plugs into the canister solenoid valve. It's purpose is to vent the gas tank. The solenoid valve opens at cruse to provide some extra fuel.

+1 that is the exact reason(s) I decided to keep the EGR and Charcoal Canister.

But what you can do is delete the coolant lines that go to the EGR spacer (if you don't drive the stang in the winter, the coolant is for cold starts).
 
soontobefastfox;7194448(if you don't drive the stang in the winter said:
It's to cool down the hot EGR spacer. If the EGR is deleted, so can the lines.


It can't really help with cold starts because the coolant doesn't warm up til 10 minutes after the car has been started
 
Let it vent, but route it in an area where vapors won't be trapped.

Remember, gasoline vapors are explosive in the right concentration level.


Oh and She is hot!
 
Down low in the front bumper so the fumes go out under the car? Can I just lengthen the line and relocate the charcoal box behind the bumper so its out of site? I don't really want my car to explode.

That is the way to go. Inside the fender would work well also (this is where they put the cannister on 5N95's).

Good luck.
 
On the canister, there is a smaller line that comes from through the firewall, and there is a bigger line (mine is unhooked, the kid I bought the car from eliminated the smog pump and a/c) this line is not there. Where does the bigger line go? Or is that a vent? Just trying to figure out all the cob jobs that were performed on my car.

Thanks guys!:shrug:
 
it's a vacuum like that runs up into the front of the intake manifold. It connects underneath on the front side.

Look for a vac line coming out..unless you have aftermarket intake.

Basically the vapors are brought into the engine and combusted after passing through activated charcoal
 
I deleted all that stuff.. I actually found a tiny AND I MEAN EXTREMELY TINY FILTER THAT k&N MAKES AND I PUT IT AT THE END tHE FILTERE OF THE LINE.. IT DEFINITLY HELPED WITH THE GAS SMELL.. AND THEIR FILTERS ARE GOOD FOR LIFE,, I CLEAN IT WHEN I DO OIL CHANGES,,,THE FILTER IS ABOUT TWO THUMB WDITHS WIDE AND THE INLET IS AS SMALL AS THE VENT LINE.... WORKED GREAT
 
it's a vacuum like that runs up into the front of the intake manifold. It connects underneath on the front side.

Look for a vac line coming out..unless you have aftermarket intake.

Basically the vapors are brought into the engine and combusted after passing through activated charcoal

I'm running a Track Heat intake. Can just vent the vapors out the wheel well or something? Or would you recommend relocating the box so its hidden?
 
Personally, i would relocate the box.


The other line just needs to see vacuum from the manifold. Do you have any spare vac ports on the manifold where you can run a vac line to from the canister.

I wouldn't vent it. You are venting gasoline vapors from your fuel tank. You don't want to take a chance and start an underhood fire. Just hide the box which weighs 2 pounds and route the vac line to the intake