Elbow Deep in Dex!!!!! 56K Warning.

69Rcode_Mach1

Active Member
Apr 20, 2004
1,473
1
37
Salt Lake City, Utah
I finally took the tranny apart. I bought it rebuilt off of corral. I verified that it is a T-5Z by counting the number of revolutions of the input shaft and the 1st gear. It was 3 turns exactly. So it must be the 2.95 which is the Z-spec. Anyway the thing was having problems going into gear, sometimes it went right in and sometimes it was like hitting a brick wall and would not go in. I called D&D they said it was a clutch issue, which means my stupid hydraulic clutch wasn't disengaging, but it could be synchros, or bent shift forks which is unlikely. But while it is out I would like to have the peace of mind to make sure it is built right. Anyway I want to check out the synchros and shift forks to make sure that the internals are okay. Here are some pics for you guys. I have some vids but don't know how to put them up. I am searching to find them. Here are the pics.

Tranny001.webp


Tranny002.webp


Tranny003.webp


Tranny004.webp


Tranny005.webp


Tranny006.webp


Tranny007.webp


Tranny008.webp


Tranny009.webp


Tranny010.webp


Tranny012.webp


Tranny013.webp


Tranny015.webp


Tranny016.webp


Tranny017.webp


Tranny018.webp
 

Attachments

  • Tranny001.webp
    Tranny001.webp
    25.6 KB · Views: 166
  • Tranny002.webp
    Tranny002.webp
    20.5 KB · Views: 170
  • Tranny003.webp
    Tranny003.webp
    19.4 KB · Views: 211
  • Tranny004.webp
    Tranny004.webp
    20.5 KB · Views: 143
  • Tranny005.webp
    Tranny005.webp
    26.8 KB · Views: 183
  • Tranny006.webp
    Tranny006.webp
    30.1 KB · Views: 169
  • Tranny007.webp
    Tranny007.webp
    19.7 KB · Views: 199
  • Tranny008.webp
    Tranny008.webp
    23.4 KB · Views: 216
  • Tranny009.webp
    Tranny009.webp
    20.4 KB · Views: 208
  • Tranny010.webp
    Tranny010.webp
    14.8 KB · Views: 179
  • Tranny012.webp
    Tranny012.webp
    15.5 KB · Views: 153
  • Tranny013.webp
    Tranny013.webp
    17.3 KB · Views: 220
  • Tranny015.webp
    Tranny015.webp
    34.3 KB · Views: 187
  • Tranny016.webp
    Tranny016.webp
    26 KB · Views: 191
  • Tranny017.webp
    Tranny017.webp
    20.1 KB · Views: 150
  • Tranny018.webp
    Tranny018.webp
    19.3 KB · Views: 174
http://videos.streetfire.net/player....7-BA7C096E18A0

http://videos.streetfire.net/Player....9-E196664AC2C1

http://videos.streetfire.net/player....A-4F6A307BDC60

http://videos.streetfire.net/player....7-63C75DA7DEE2
I don't plan on having this tranny last much longer than a year or two at the most before my engine grenades it. Then I am upgrading it with a G-force. This is just temporary but it has to work. Hope these vids help. I want you guys to help me spot anything out of the ordinary. I am hoping it was just the clutch not disengaging properly.
 
looks good to me, First gear is the largest gear toward the rear of the trans, the syncros look good in the pick, they look new, check the 1-2 slider, look toward the inner diameter of the slider and check the teeth that mate up to the first gear syncro. They should be pointed and not rounded over.

I had problems with the slider teeth being worn and not engagine the gears as they should, of course this was 2nd gear, things are different for first gear since the car is usually at idle when it engages. Did you ever try downshifting into first when the car was already moving?
 
i dunno if this helps but, i just put my t5z in this week, and it felt a little notchy in 1st and 2nd........it went in ok, just a little stiffer than 3rd and 4th......i turned my fire wall adjuster out one more turn and it seemed to help it some......

thats the problem with a hydraulic clutch.......it's harder to 'feel' what the clutch is doing.....

damn man.......lets see here, with a .63 overdrive 5th gear (t5z 5th gear) and a 2.75 rear end gear......your cruise on the freeway will be what like 1200 rpms??? lol...you'll be idling......:D