• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Engine Rebuild Time?

  • Thread starter Thread starter 72gs455
  • Start date Start date Aug 11, 2017
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 11, 2017
#1
  • Aug 11, 2017
  • #1
So after work I fired up the foxbody went to my secret spot did a few burn outs some donuts here and there but after doing one last donut it sounded like my engine got a knock and lost power and started to back fire like crazy (wont go over 1200ish-1500ish rpms with out it backfiring) engine only had 139k miles now is this fixable or do I just pull the sucker out and rebuild it

the file im trying to upload is to big so ill link to youtube

View: https://www.youtube.com/watch?v=coX5tMIdM_Q
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Aug 11, 2017
#2
  • Aug 11, 2017
  • #2
Sounds like you may have lost a rocker. Pull the upper intake and both valve covers. Its hard to tell through video but sounds like top end noise....would cause a hell of a miss too.
 
Reactions: revhead347, Davedacarpainter and Black1987
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 11, 2017
#3
  • Aug 11, 2017
  • #3
alright ill do that and report back when im done
 
Reactions: 90sickfox
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 17, 2017
#4
  • Aug 17, 2017
  • #4
Bump!

so it was rocker arm
so question now is can i replace this arm? or must i replace all of them?
 

Attachments

  • 20863389_1510998405622986_2357940130553150812_o.webp
    155 KB · Views: 256
Reactions: 90sickfox

mikestang63

SN Certified Technician
Aug 27, 2012
11,606
8,859
214
In the garage
Aug 17, 2017
#5
  • Aug 17, 2017
  • #5
72gs455 said:
Bump!

so it was rocker arm
so question now is can i replace this arm? or must i replace all of them?
Click to expand...

You have pedestal type rockers so theoretically you could just replace the one. What does the bolt hole in the head where the rocker was secured look like- is it stripped. Why did it back out.
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Aug 17, 2017
#6
  • Aug 17, 2017
  • #6
Roll that push rod on a flat surface and check to see if it bent.

It is kinda weird that that bolt came out of the head.

The head may be able to be fixed but that area takes a lot of stress. A properly installed Helli Coil may hold it together.

I'm an over rev condition it isn't uncommon for the lifter to jump up of the camshaft and break the dog bone lifter keeper. The only way to check that is to remove the lower intake....and use a magnet to pull the lifter out of its bore. You want to check the roller at the bottom of the lifter for damage.

So far it doesn't look like an expensive fix.

It doesn't look too bad. Usually, blow by and worn out motors will cause carbon to build up all over the inside of the engine. I've seen them so bad that you couldn't see the rocker bolt heads. I had to chip it away to get a socket on them....and that car still ran.
 
Reactions: A5literMan
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 21, 2017
#7
  • Aug 21, 2017
  • #7
BUMP

So I installed the new rocker but it had load of play
do i need to shim it?
heres a video
View: https://www.youtube.com/watch?v=AWQZDkAsUNQ
 

Dan02gt

mazing how much gas smell came from that tiny hole
20+ Year Stangneter
Mar 2, 2003
909
415
113
Greenville, NC
Aug 21, 2017
#8
  • Aug 21, 2017
  • #8
You shouldn't have to shim a stock rocker. Something else is wrong. Check out the pushrod and make sure it's not bent and if it is OK move on to the lifter.
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 21, 2017
#9
  • Aug 21, 2017
  • #9
the pushrod is straight almost like new
 

Jersey Joe

I remember blowing that Monkey's ass
10 Year Member
Nov 29, 1999
767
1,319
154
Bloomingdale N.j.
Aug 21, 2017
#10
  • Aug 21, 2017
  • #10
Maybe collapsed or broken lifter ?
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 21, 2017
#11
  • Aug 21, 2017
  • #11
okay so when i tapped the helli coil i forgot to clean out the hole of metal so right now im cleaning it out ill report back in a few
 
Reactions: 90sickfox
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 22, 2017
#12
  • Aug 22, 2017
  • #12
Okay some updates

After fixing the hellicoil the stud threaded but on the first start click click click removed the valve cover the rocker arm was loose but this time the one next the first stripped so I tightened to 25 pounds and now the car starts but shuts down right after do I have to preload the rockers before torquing down?
 

FoxMustangLvr

I love my Pimp
SN Certified Technician
Oct 14, 2012
4,968
3,514
204
Spokane, Wa
Aug 22, 2017
#13
  • Aug 22, 2017
  • #13
72gs455 said:
Okay some updates

After fixing the hellicoil the stud threaded but on the first start click click click removed the valve cover the rocker arm was loose but this time the one next the first stripped so I tightened to 25 pounds and now the car starts but shuts down right after do I have to preload the rockers before torquing down?
Click to expand...
To pump up a lifter you could unplug your coil wire and try to start your car for a few seconds. The oil pump will prime the motor. Plug coil wire back in and fire it up. If this doesn't work then what @90sickfox said needs to be done which is remove lower intake and check the condition of the hyd. lifter. It may have failed. Also check for any vacuum hoses that you may have forgotten to reconnect or may have broken upon removal. They are old and can crack or break when handled.
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 22, 2017
#14
  • Aug 22, 2017
  • #14
this was the first start up
View: https://www.youtube.com/watch?v=eLI_hnYeiqU



after this i unbolted the rocker arm and torqued it down again and now its starts but shut off
i dont have time to remove the intake all that good stuff my best bet is i might just take to a mechanic if "priming the lifter" doesn't work
no vacuum leaks from what i can see
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Aug 22, 2017
#15
  • Aug 22, 2017
  • #15
Starting the car primed the lifter. It doesn't take a long time at all to pull the lower intake and put it back on. I once pulled the heads off a mustang on the side if the street and installed new head gaskets in about 3 hours.

Keep in mind that if that lifter did break a dig bone keeper and spun sideways it will harm the camshaft. That's a little more work. You don't want to run the car too much like that because it could mushroom the lifter and scar the bore....if that happens you'll need a new block.

I remember going down that road with one of my cars. Luckily I caught it before it did damage to the lifter bore. Had to replace the lifter, dog bone keeper, and the camshaft....my rocker was ok.
 
Reactions: 72gs455
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 22, 2017
#16
  • Aug 22, 2017
  • #16
yeah man im going to dig into tomorrow thanks for the input everyone!
 
7

72gs455

Member
Jun 16, 2017
28
5
13
Aug 31, 2017
#17
  • Aug 31, 2017
  • #17
quick update there seem to be no damage in the lifters after removing the lower intake everything seems okay
 
Reactions: Jersey Joe
7

72gs455

Member
Jun 16, 2017
28
5
13
Sep 1, 2017
#18
  • Sep 1, 2017
  • #18
okay heres my last go before i just yank the engine and rebuild it
all hydraulic roller lifters are okay none of them are collapsed nothing broken (at least no metal shavings)
push rods are fine none are bent
from what i can see the cam seem to be fine.. since the lifters had no damage i assume the cam is okay
both rocker arm studs seem to get "tight" before they lock down the rocker what could cause this?
this is how all the lifter looked like
View: https://www.youtube.com/watch?v=Ox43Ek28KNM


im at a lost in what the problem is
 

revhead347

Apparently my ex-husband made that mistake.
20+ Year Stangneter
Jun 14, 2004
9,303
1,649
214
Acworth, GA
Sep 1, 2017
#19
  • Sep 1, 2017
  • #19
Run a compression test. Make sure you don't have a bent valve.

Kurt
 
You must log in or register to reply here.

Similar threads

Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
W
Blue smoke..
  • Wicked_Rpm
  • Aug 11, 2024
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
567
1996 - 2004 SN95 Mustang -General/Talk- Aug 14, 2024
weendoggy
O
TransGo shift kit question?
  • optionizerSS
  • Jul 5, 2023
  • 1994 - 1995 Specific Tech
Replies
8
Views
2K
1994 - 1995 Specific Tech Jul 7, 2023
AeroCoupe
L
Engine 97 mustang gt manual weird idol when off the throttle and coasting in 3rd, 4th, or 5th
  • Lanezs
  • Jun 9, 2023
  • SN95 4.6L Mustang Tech
Replies
3
Views
2K
SN95 4.6L Mustang Tech Dec 20, 2023
Yel2002GTAuto
Y
SN Mustang Magnum T56 swap
  • revhead347
  • May 24, 2024
  • 1994 - 1995 Specific Tech
Replies
15
Views
7K
1994 - 1995 Specific Tech Jun 28, 2026
GearHeadGuy
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?