Engine Rebuild Time?

72gs455

Member
Jun 16, 2017
28
5
13
So after work I fired up the foxbody went to my secret spot did a few burn outs some donuts here and there but after doing one last donut it sounded like my engine got a knock and lost power and started to back fire like crazy (wont go over 1200ish-1500ish rpms with out it backfiring) engine only had 139k miles now is this fixable or do I just pull the sucker out and rebuild it

the file im trying to upload is to big so ill link to youtube


View: https://www.youtube.com/watch?v=coX5tMIdM_Q
 
Bump!

so it was rocker arm
so question now is can i replace this arm? or must i replace all of them?
 

Attachments

  • 20863389_1510998405622986_2357940130553150812_o.webp
    20863389_1510998405622986_2357940130553150812_o.webp
    155 KB · Views: 256
  • Like
Reactions: 90sickfox
Roll that push rod on a flat surface and check to see if it bent.

It is kinda weird that that bolt came out of the head.

The head may be able to be fixed but that area takes a lot of stress. A properly installed Helli Coil may hold it together.

I'm an over rev condition it isn't uncommon for the lifter to jump up of the camshaft and break the dog bone lifter keeper. The only way to check that is to remove the lower intake....and use a magnet to pull the lifter out of its bore. You want to check the roller at the bottom of the lifter for damage.

So far it doesn't look like an expensive fix.

It doesn't look too bad. Usually, blow by and worn out motors will cause carbon to build up all over the inside of the engine. I've seen them so bad that you couldn't see the rocker bolt heads. I had to chip it away to get a socket on them....and that car still ran.
 
  • Like
Reactions: A5literMan
You shouldn't have to shim a stock rocker. Something else is wrong. Check out the pushrod and make sure it's not bent and if it is OK move on to the lifter.
 
Okay some updates

After fixing the hellicoil the stud threaded but on the first start click click click removed the valve cover the rocker arm was loose but this time the one next the first stripped so I tightened to 25 pounds and now the car starts but shuts down right after do I have to preload the rockers before torquing down?
 
Okay some updates

After fixing the hellicoil the stud threaded but on the first start click click click removed the valve cover the rocker arm was loose but this time the one next the first stripped so I tightened to 25 pounds and now the car starts but shuts down right after do I have to preload the rockers before torquing down?
To pump up a lifter you could unplug your coil wire and try to start your car for a few seconds. The oil pump will prime the motor. Plug coil wire back in and fire it up. If this doesn't work then what @90sickfox said needs to be done which is remove lower intake and check the condition of the hyd. lifter. It may have failed. Also check for any vacuum hoses that you may have forgotten to reconnect or may have broken upon removal. They are old and can crack or break when handled.
 
Starting the car primed the lifter. It doesn't take a long time at all to pull the lower intake and put it back on. I once pulled the heads off a mustang on the side if the street and installed new head gaskets in about 3 hours.

Keep in mind that if that lifter did break a dig bone keeper and spun sideways it will harm the camshaft. That's a little more work. You don't want to run the car too much like that because it could mushroom the lifter and scar the bore....if that happens you'll need a new block.

I remember going down that road with one of my cars. Luckily I caught it before it did damage to the lifter bore. Had to replace the lifter, dog bone keeper, and the camshaft....my rocker was ok.
 
  • Like
Reactions: 72gs455
okay heres my last go before i just yank the engine and rebuild it
all hydraulic roller lifters are okay none of them are collapsed nothing broken (at least no metal shavings)
push rods are fine none are bent
from what i can see the cam seem to be fine.. since the lifters had no damage i assume the cam is okay
both rocker arm studs seem to get "tight" before they lock down the rocker what could cause this?
this is how all the lifter looked like

View: https://www.youtube.com/watch?v=Ox43Ek28KNM


im at a lost in what the problem is