Explorer Intake Value

865.0HO · Nov 2, 2009

I was wondering what these are worth, what price would be considered a good deal? I was browsing through the wrecking yard this morning and found a 98' Explorer upper/lower intake. Emissions aren't an issue in my area, so EGR passages aren't a big concern to me.

If the price is right, what else should I grab with the intake? It's a CFC vehicle so I assume the heads are ruined.

Thanks,

Jeremiah

1990Coupe · Nov 2, 2009

I got mine off a burned mountaineer.. I paid like 25 bucks for it.. I think they normally go for like 50-100 bucks? I may be totally wrong though.

Mustang5L5 · Nov 2, 2009

Price has come down a lot since there are so many available. Last Exploder made with the 5.0 was 2000...so 10- 14 years means a lot are off the roads and flooding the junkyards.

I've seen heads go for $200 and Intakes for less than that..maybe $100-150. A lot of guys buying them at the yards get them for even less than that

tannerc91gt · Nov 2, 2009

But craigslist lists them higher because to put it simply, people are stupid, I wouldn't pay more that what 5l5 said, although the
non-p heads still seem to go for $300ish in my area

865.0HO · Nov 2, 2009

They want $110+tax, which would be about $118. I think I'll check back in a week or two and offer them $100 out the door and see if they'll take it.

tannerc91gt · Nov 2, 2009

I'd take it before someone else does....

Coast2CoaStang · Nov 2, 2009

I paid $59.50 for a complete upper and lower Exploder intake out of a pick-n-pull in the San Fernando valley. I also paid $60 total, for a complete pair of "P" heads off the same vehicle.

stykthyn · Nov 2, 2009

if its a cfc car you cant grab the intak either

5.0Droptop · Nov 2, 2009

stykthyn said:
if its a cfc car you cant grab the intak either

I thought the JY's could sell parts off the CFC cars??

lanky83 · Nov 2, 2009

There going for 125.00 or so in and around Indy.

tannerc91gt · Nov 2, 2009

Motor can't be sold, trans and rear end can be sold but must be sold to seperate parties. And then the body is parted out. Motors are supposed to be crushed. But some junkyards may not follow the rules very well

Mustang5L5 · Nov 2, 2009

I was in a yard today and saw a few CFC cars with people picking parts off them.

Even saw a bottle of the "liquid glass" used to seize up the engines...how sad.

One car was an early 00's Mountaineer. It was in GREAT shape. Sad they trashed it

stykthyn · Nov 3, 2009

at the PNP here about 40% of the cars are now CFC cars. 3 of them v8 explorers. what a shame. there was also a GTP, a very nice Bronco, and probably one of the cleanest nissan 240's ive ever seen

Mustang5L5 · Dec 30, 2009

Just a head up, surfing CL and found at least 3 sets of Explorer intakes for ~ $100 complete.

I picked up an '97 Explorer Intake complete, w/internal EGR for $75

Like i said, the market is FLOODING with these intakes and you can get them dirt cheap. I actually needed only the lower intake so i could port it and then swap it out with my Cobra lower...but i figured i'd get the entire intake for the same price as a used Cobra lower and then sell off the upper.

mob · Dec 30, 2009

You gotta find a junkyard that has set prices, not a junkyard that decides what to charge you by what you look like. My local junkyard has a set price list, like 25 bucks for any aluminum intake, 50 bucks for an iron head, whether its a gt40p or the crappiest head you can find.

beyondspexj · Dec 30, 2009

i got mine for $100 from my local jy.

and out here with cfc cars/trucks, you cannot sell the short block. i could have pulled the heads as well but didnt have the funds lol.

stykthyn · Dec 31, 2009

i normally sell mine for 150 but they are stripped, painted, come with 24lb injectors, and the tb modified to work on a mustang.

Mustang5L5 · Dec 31, 2009

How do you guys strip your intakes??

I wanna clean my lower up before i send it out to get ported, but idon't want to sandblast out of fear of getting sand behind the baffle

stykthyn · Dec 31, 2009

a pair of vice grips will pull out the studs holding the baffle. when you are done blasting/painting tap the holes and put the baffle back on with bolts.

Explorer Intake Value

865.0HO

Member

1990Coupe

Mustang5L5

That is…until I whipped out my Bissell

tannerc91gt

This last 25% is foreign territory at this point

865.0HO

Member

tannerc91gt

This last 25% is foreign territory at this point

Coast2CoaStang

Member

stykthyn

I want to measure mine. It doesn't look that tall.

5.0Droptop

...all those nights we shared, and you're a dude??

lanky83

Member

tannerc91gt

This last 25% is foreign territory at this point

Mustang5L5

That is…until I whipped out my Bissell

stykthyn

I want to measure mine. It doesn't look that tall.

Mustang5L5

That is…until I whipped out my Bissell

mob

the guy who hits on his mom

beyondspexj

Member

stykthyn

I want to measure mine. It doesn't look that tall.

Mustang5L5

That is…until I whipped out my Bissell

stykthyn

I want to measure mine. It doesn't look that tall.

Similar threads

Explorer Intake Value

Member

That is…until I whipped out my Bissell

This last 25% is foreign territory at this point

Member

This last 25% is foreign territory at this point

Member

I want to measure mine. It doesn't look that tall.

...all those nights we shared, and you're a dude??

Member

This last 25% is foreign territory at this point

That is…until I whipped out my Bissell

I want to measure mine. It doesn't look that tall.

That is…until I whipped out my Bissell

the guy who hits on his mom

Member

I want to measure mine. It doesn't look that tall.

That is…until I whipped out my Bissell

I want to measure mine. It doesn't look that tall.

Similar threads

Privacy & Transparency

Privacy & Transparency