• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

explorer pieces

  • Thread starter Thread starter undercnstrction
  • Start date Start date Dec 21, 2009
  • 1
  • 2
Next
1 of 2 Next Last
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 21, 2009
#1
  • Dec 21, 2009
  • #1
i know the v-8 ford explorer uses the same intakes as the cobra, but did i read correctly that the v-8 ford explorer has the same heads as the cobra???

here's part 2: are those heads the same as GT40 heads?
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Dec 21, 2009
#2
  • Dec 21, 2009
  • #2
you read right. bolt up em and flat foot the loud pedal
 
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 21, 2009
#3
  • Dec 21, 2009
  • #3
LMAO!!! thanx
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Dec 21, 2009
#4
  • Dec 21, 2009
  • #4
I answered as best as I could in your pm, but to sum it up for anyone else that doesnt know. the iron gt40 heads are the same heads that are on the 93-95 cobras but with different valve springs. change the springs and they are a direct bolt on. the gt40 p heads also require a spring swap along with the addition of p specific headers to allow access to the spark plugs.
 

tat2d30688

Member
Jul 14, 2009
88
0
7
Chesapeake, Va
Dec 21, 2009
#5
  • Dec 21, 2009
  • #5
What years were the gt4o's and which were the gt40p's
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Dec 22, 2009
#6
  • Dec 22, 2009
  • #6
he's new. no need to go off on him.....
 

302Feen

New Member
Dec 22, 2009
52
0
0
Dec 22, 2009
#7
  • Dec 22, 2009
  • #7
tat2d30688 said:
What years were the gt4o's and which were the gt40p's
Click to expand...

1996-early '97 used the standard GT40 heads. '97-'01 used the "P" heads.

You can simply look at the spark plug angle to tell the difference.

Just FYI to the OP- If you're interested in an Explorer intake/injectors send me a PM.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Dec 22, 2009
#8
  • Dec 22, 2009
  • #8
There is a difference between the explorer GT40's and the 93-95 Cobra GT40's...aside from the valve springs.

The explorer versions lack the provisions for the air pump tube that connects to the rear of the heads.
 
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 23, 2009
#9
  • Dec 23, 2009
  • #9
Mustang5L5 said:
There is a difference between the explorer GT40's and the 93-95 Cobra GT40's...aside from the valve springs.

The explorer versions lack the provisions for the air pump tube that connects to the rear of the heads.
Click to expand...

another stupid question......can you explain what "air pump" you're referring to? i'm trying to think what was on the back of the heads when i took them off the motor and it's not clicking in? does this mean that the heads off of an explorer cannot/should not be used?
 
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 23, 2009
#10
  • Dec 23, 2009
  • #10
the reason i'm asking all of the questions about the explorer setups is because i have the chance to pick up 2 sets of v-8 explorer heads and intakes for a pretty good price. the greedy capitalist in me is trying to determine if i can flip the pieces and funnel the money into my own project.

hope this idea doesn't offend anyone
 

302Feen

New Member
Dec 22, 2009
52
0
0
Dec 23, 2009
#11
  • Dec 23, 2009
  • #11
undercnstrction said:
another stupid question......can you explain what "air pump" you're referring to? i'm trying to think what was on the back of the heads when i took them off the motor and it's not clicking in? does this mean that the heads off of an explorer cannot/should not be used?
Click to expand...

The "air pump" he's talking about is your smog pump. It should be the bottom pulley on the passenger side. It has two tubes that come out of it... one tube goes to the back of your heads, and the other tube goes to your midpipe.
 
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 23, 2009
#12
  • Dec 23, 2009
  • #12
got it. thanx.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Dec 23, 2009
#13
  • Dec 23, 2009
  • #13
unless you are going to use them for your own car I would pass. now is not a great time to try and flip parts. I have several explorer top ends that have been in my shed for over a year now b/c no one wants to pay what they are worth and then pay to have them shipped on top of that.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Dec 23, 2009
#14
  • Dec 23, 2009
  • #14
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.
 
U

undercnstrction

New Member
Nov 10, 2009
312
0
0
Dec 23, 2009
#15
  • Dec 23, 2009
  • #15
Mustang5L5 said:
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.
Click to expand...


if you are paying $75 for the lower, i can get the upper AND lower for less than you are going to pay for just the lower.

i'm seeing GT40 heads going for anywhere from $150-300 on corral. the ones i'm looking at are less than that.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Dec 23, 2009
#16
  • Dec 23, 2009
  • #16
undercnstrction said:
if you are paying $75 for the lower, i can get the upper AND lower for less than you are going to pay for just the lower.
Click to expand...

Nope....$75 for both. I could prob haggle a little lower, but the intake is clean.


Junkyard near me wanted $40, but i am too lazy to deal with getting dirty and pulling it off myself. I think they wanted $75 for the heads too. Again...it's 20 degrees out and i don't want to sit there covered in grease pulling dirty parts off and put them in the trunk of my car. There are at least 4 exploders in my hard. To me, the cost of flipping them didn't justify the labor involved...esp when i see the prices of the heads and intake falling all the time.
 

NIKwoaC

中國製造
15 Year Member
Oct 31, 2006
5,525
943
214
Chengdu Province
Dec 23, 2009
#17
  • Dec 23, 2009
  • #17
Ha, I paid $175 for my Explorer intake a couple years back. Now I feel like the guys who bought PS3s when they first came out.
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Dec 26, 2009
#18
  • Dec 26, 2009
  • #18
stykthyn said:
I answered as best as I could in your pm, but to sum it up for anyone else that doesnt know. the iron gt40 heads are the same heads that are on the 93-95 cobras but with different valve springs. change the springs and they are a direct bolt on. the gt40 p heads also require a spring swap along with the addition of p specific headers to allow access to the spark plugs.
Click to expand...

negative noober!! pretty much all sbf headers will work, you just have to get creative with the plug wires.. ask mr BK_cheeze and myself.. your 93 vert had p heads with standard bbk shorties on it, and it was all good in the hood..
 

striker911

Member
Aug 6, 2008
156
1
18
Mountain Home, AR
Dec 26, 2009
#19
  • Dec 26, 2009
  • #19
Mustang5L5 said:
Explorer stuff is dirt cheap today. Maybe 5 years ago you could flip them, but with the amount of 5.0 exploders in yard now, they are plentiful and cheap.

I'm actually in the middle of buying one off CL for $75 complete just for the lower intake alone.
Click to expand...

plentiful and cheap? I live in a pretty big city and hit 2 of the three biggest junk yards the other day. Scored on a TB and thats it. Seen only 2 v8 exploders and motors where gone. I must have bad luck. I am about to move to a diff state too and have credit at the yard I did go to. Guess I wont get my money if I cant find parts I need. Sucks. If the intake is $40 and I have $35 credit then its almost free. If only they had one.

This is my problem. Pay $5 @ the junk yard or buy for $200 on ebay. Screw it, if anyone lives in the Kansas City metro area needs this credit give me half the cash and its yours. I move in three weeks.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Dec 28, 2009
#20
  • Dec 28, 2009
  • #20
Mr. Rustypwnz said:
negative noober!! pretty much all sbf headers will work, you just have to get creative with the plug wires.. ask mr BK_cheeze and myself.. your 93 vert had p heads with standard bbk shorties on it, and it was all good in the hood..
Click to expand...

did you have to use those ghey cut to fit plug wires? bah, flip your headers over like Mob did and put a blow dryer on there.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

N
Looking for ECU/CHIP for 1992 5.0
  • Nathan26
  • Sep 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
335
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 8, 2026
Qtrhrse23
Ford truck engine swap issues
  • keel
  • Jul 7, 2026
  • Other Auto Tech
Replies
17
Views
775
Other Auto Tech Jul 13, 2026
General karthief
P
Vacuum
  • ProTechAutoServices
  • Aug 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
340
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
Cooling Jacket Pitting Idea's?
  • BoostedRed89gt
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
12
Views
358
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 17, 2026
Mustang5L5
B
97 GT with 03 explorer Eddie Bauer edition 4.6l
  • basbill73
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
149
1996 - 2004 SN95 Mustang -General/Talk- May 11, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?