• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Foxbody Brake Upgrade

  • Thread starter Thread starter MileHi91LX
  • Start date Start date Sep 24, 2016
M

MileHi91LX

Member
Aug 25, 2016
49
4
18
Sep 24, 2016
#1
  • Sep 24, 2016
  • #1
I'm running the NRC big brake kit up front. I am planning to keep the stock booster and upgrade to a 93 cobra MC. I have to decide between '94 and '03 spindles I have. My questions are now:
1) if I buy a Max Motorsports stock prop. Valve delete kit do I still need to buy their plug bolt, extra $16
2) I'm guessing I absolutely need the new bias pro portioning valve
3) I'm planning on buying the MM adapter line kit for the new '93 Cobra MC to stock brake lines
4) What else do I need?
 

TOOLOW91

If you're the village idiot what's that make me?
20+ Year Stangneter
Nov 29, 1999
8,501
8,763
234
S.I.NY
Sep 24, 2016
#2
  • Sep 24, 2016
  • #2
You want the 94 spindles to keep the geometry correct.

If you're running cobra calipers up front and disc in the rear you'll want a 93 cobra booster and 94/95 cobra master.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Sep 25, 2016
#3
  • Sep 25, 2016
  • #3
1: no

2: yes

The nrc BBk more than likely comes with 99-04 cobra calipers, which the proper mc to use would be the 1993 cobra mc if equipped with sn95 rear disk as well, however, if adamant about not swapping the booster, one should run the smaller 94-95 cobra mc instead to gain extra assist. I would highly recommend doing the booster swap though. Without it, your braking performance won't be worth performing.


If you are keeping drums out back. Then you can't use any 4 wheel disk mc. Pedal will be stiff as a board. Only option is to leave the stock mc.


Sent from my big ass iPhone 6 using Tapatalk
 
M

MileHi91LX

Member
Aug 25, 2016
49
4
18
Sep 25, 2016
#4
  • Sep 25, 2016
  • #4
I'm running a disc brake setup out back from the 99-04 vintage. Copy that I need a better booster. I'm concerned with the Anderson B41 cam and a Procharger am I going to have enough vacuum to power the booster?
 
M

MileHi91LX

Member
Aug 25, 2016
49
4
18
Sep 25, 2016
#5
  • Sep 25, 2016
  • #5
What year booster will work? I found an '03 that's close and inexpensive.
 

Mstng93SSP

You have a nice rear end there Dave.
15 Year Member
Nov 29, 1999
2,993
3,500
184
Mililani, Hawaii
Sep 25, 2016
#6
  • Sep 25, 2016
  • #6
1993 cobra booster. Easiest install and best pedal feel. Done it more than half a dozen times. Wouldn't use anything else personally.
 
M

MileHi91LX

Member
Aug 25, 2016
49
4
18
Sep 25, 2016
#7
  • Sep 25, 2016
  • #7
I found one at O'Reilly for 84$, seems like the most inexpensive route
 

Mstng93SSP

You have a nice rear end there Dave.
15 Year Member
Nov 29, 1999
2,993
3,500
184
Mililani, Hawaii
Sep 26, 2016
#8
  • Sep 26, 2016
  • #8
Yeah, they are not that expensive. To get it to go in you will probably have to elongate the two holes on the left side (as you look at it from the front under the hood) that the booster studs go through. That is the easiest way from my experience. There is a lot of information out there about the booster install.
 
Reactions: FoxMustangLvr

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Sep 26, 2016
#9
  • Sep 26, 2016
  • #9
99-04 v6 booster is essentially the same. Only difference is the studs are metric, and one is slightly off. Not a huge deal.

Make sure you get the nuts that come with it otherwise take it to hardware store to match it up with hardeare before installing it.

Then mAke a template of cardboard to fit the studs, then transfer it to the firewall and Mark which stud hole you have to drill. Then slot all 4 to the pass side.

I did a 94-95 booster, which is the same, and it wasn't a big deal. Did not hammer my strut tower. I removed the upper intake to give me room, but it wasn't necessary.

Hardest part is under the dash. Extensions and universals are your friend here


Sent from my big ass iPhone 6 using Tapatalk
 
Last edited: Sep 26, 2016
You must log in or register to reply here.

Similar threads

Fox Brake pedal too stiff
  • keel
  • Sep 21, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
33
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 11, 2026
keel
Brake pad and rotor upgrade
  • Sparky714
  • Aug 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
669
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 17, 2026
Sparky714
8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
637
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
A
SN95 Hydroboost in a Fox | Brake lines
  • arc_jpiv
  • Sep 4, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
462
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 14, 2026
2000xp8
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
313
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?