• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-

Front bumper install... Difficult???

  • Thread starter Thread starter 2003_GT
  • Start date Start date Dec 20, 2008
2

2003_GT

New Member
Nov 5, 2008
69
0
0
Santa Fe, NM
Dec 20, 2008
#1
  • Dec 20, 2008
  • #1
I am going to remove and replace my front bumper on my 03 GT, i never done this before so i wanted to know if it was difficult to do, steps would be helpfull along with some pics PLEASE, i also want to know what tools i might need and anything else i might need to buy to hold and keep the bumper in place and stuff like that

Thanks in advance to everybody :SNSign:
 

Brute03

Member
Mar 20, 2006
232
0
16
Dec 20, 2008
#2
  • Dec 20, 2008
  • #2
it's pretty straight foward, pull the headlights, remove the screws that hold the the two vertical post the the header panel, then pull the fender liner out slightly to gain acess to the two nuts that secure the bumper to the side of the car. underneath there may be a few plastic push-pins.

i did it by myself, but it's best to have an extra set of hands to help lower it
 
2

2003_GT

New Member
Nov 5, 2008
69
0
0
Santa Fe, NM
Dec 20, 2008
#3
  • Dec 20, 2008
  • #3
will i need to buy more pushpins???
 
J

jprovence

New Member
May 20, 2007
195
0
0
Albany, OR
Dec 20, 2008
#4
  • Dec 20, 2008
  • #4
2003_GT said:
will i need to buy more pushpins???
Click to expand...

Not if you are careful and don't break them.
 

Black_02_GT

Member
Mar 2, 2008
0
0
16
Mississippi
Dec 20, 2008
#5
  • Dec 20, 2008
  • #5
The two right under the hood next to the grille, you need to be careful when you're pushing and pulling those around. They can break very easily if you're no watching what you're doing. Also on the sides of the bumper right under the fender dont there are 2 bolts on each side. When you go to put it back on do not over-tighten them at all as they will break all and you will have a slight problem.
 

evil281

New Member
Jan 6, 2008
276
0
0
Arizona
Dec 21, 2008
#6
  • Dec 21, 2008
  • #6
easy as pie, installed my cobra bumper in 30 mins by myself
 
B

blksq10psi

Member
Aug 1, 2008
114
0
16
PHILLY
Dec 21, 2008
#7
  • Dec 21, 2008
  • #7
a 12 mm gear wrench will work good for the nuts that are in the fenderliner
 

flstang65

10 Year Member
Dec 6, 2007
1,484
135
94
SE Georgia
Dec 21, 2008
#8
  • Dec 21, 2008
  • #8
2003_GT said:
will i need to buy more pushpins???
Click to expand...


whenever i remove push pins, u usually just replace them because they are very cheap.
 
2

2003_GT

New Member
Nov 5, 2008
69
0
0
Santa Fe, NM
Dec 21, 2008
#9
  • Dec 21, 2008
  • #9
Thanks for all the replys guys, ill be putting on my new bumper tomorrow morning so i just wanted some tips on how to do it, thanks again!!
 
You must log in or register to reply here.

Similar threads

S
Front bumper repair - part identification
  • Smurf20
  • Oct 24, 2025
  • 2015 - 2023 (S550) Mustang -General/Talk
Replies
2
Views
427
2015 - 2023 (S550) Mustang -General/Talk Nov 3, 2025
RobertWill31
R
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
298
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
D
Will 2023 (Non-Handling Pack) Mach 1 Wheels Fit A 2013 Mustang GT OK?
  • dmw_4814
  • Oct 27, 2026
  • 2010 - 2014 Specific Tech
Replies
0
Views
123
2010 - 2014 Specific Tech Oct 27, 2026
dmw_4814
D
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
468
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?