RANT!!! Fuggin chinees imported crap.

nickyb · Oct 1, 2024

Here I go again with this f in O'Reilly's distributor. I ordered and picked up a new steel gear for the old Bronco distributor I pushed the roll pin out ,pressed the gear off( thank goodness for my 12 ton press) pressed the new gear on and ran into having to drill the other side of the new gear so I can press the pin in. I went threw three bits and they don't even scratch the gear,I gotta get a carbide bit or so I'm told. Of course the second Chinese dist. From oh oh trolleys is crapping the bed. Stalled twice on my way to work ,once one the way home and hiccupped once also.
After much research and reading its best to use a ford dist. Since I can't get a new one I'm gonna put this used one in,also I have just ordered a new Dragon fire EFI dist.with wires from Amazon$139.99
There site says its better then overpriced or Chinese knock offs. Dist.
Ill do a review for all, soon as I can.

Feel free to rant about any bad parts you had the unpleasantness to deal with.

89ripper · Oct 1, 2024

Well im having trouble on my Impala SS right now. Doing the tie rods and I cant get the adjusting sleeve to thread on. Has me 2nd guessing whether its the tie rod threads or the sleeves themselves but no, the sleeves werent machined right. Shouldve double checked before trying to put them on. Supposed to be AC delco oh its china crap

Bullitt347 · Oct 2, 2024

nickyb said:
Here I go again with this f in O'Reilly's distributor. I ordered and picked up a new steel gear for the old Bronco distributor I pushed the roll pin out ,pressed the gear off( thank goodness for my 12 ton press) pressed the new gear on and ran into having to drill the other side of the new gear so I can press the pin in. I went threw three bits and they don't even scratch the gear,I gotta get a carbide bit or so I'm told. Of course the second Chinese dist. From oh oh trolleys is crapping the bed. Stalled twice on my way to work ,once one the way home and hiccupped once also.
After much research and reading its best to use a ford dist. Since I can't get a new one I'm gonna put this used one in,also I have just ordered a new Dragon fire EFI dist.with wires from Amazon$139.99
There site says its better then overpriced or Chinese knock offs. Dist.
Ill do a review for all, soon as I can.

Feel free to rant about any bad parts you had the unpleasantness to deal with.

Comp Cams makes a composite dist gear that works very well.
I use one on my race engine which sees a ton of rpm.
They ain't cheap, but they fit.

Bullitt347 · Oct 2, 2024

89ripper said:
Well im having trouble on my Impala SS right now. Doing the tie rods and I cant get the adjusting sleeve to thread on. Has me 2nd guessing whether its the tie rod threads or the sleeves themselves but no, the sleeves werent machined right. Shouldve double checked before trying to put them on. Supposed to be AC delco oh its china crap

I work at a Chevrolet Dealership. Almost all AC Delco stuff is made in China. Some of it is made in Mexico, but most is made in China.

89ripper · Oct 2, 2024

Bullitt347 said:
I work at a Chevrolet Dealership. Almost all AC Delco stuff is made in China. Some of it is made in Mexico, but most is made in China.

Yeah...I realize that now...or actually should say, for awhile now. Its a crap shoot trying to get decent parts these days

Noobz347 · Oct 2, 2024

I'm going to leave this here for the time being.

I am putting together a list of vendors and 'things' that are not made in China.

Some lead time on these but I'll put it here anyhow: https://performancedistributors.com/product/ford-duraspark-distributors/

nickyb · Oct 2, 2024

Noobz347 said:
I'm going to leave this here for the time being.

I am putting together a list of vendors and 'things' that are not made in China.

Some lead time on these but I'll put it here anyhow: https://performancedistributors.com/product/ford-duraspark-distributors/

Let's start a good parts go-to page.im in.

nickyb · Oct 2, 2024

Bullitt347 said:
I work at a Chevrolet Dealership. Almost all AC Delco stuff is made in China. Some of it is made in Mexico, but most is made in China.

I like the hecho en Mexico parts better then the R.O.C. crap

Bullitt347 · Oct 2, 2024

nickyb said:
Let's start a good parts go-to page.im in.

I am all for this.
Unfortunately, there is a majority of people who would rather buy cheap (china/mexico) (walmart) than spend more and buy American made.
Sometimes it is almost impossible to find an American made item.
I went to 5 different Hardware stores in 2 different cities to find a tape measure that was made in the USA. Yes it cost more. Yes I spent a lot of time. To me it was worth it. The urge to just cave and buy from Amazon instead of buying local is real. Most of the time, I buy local. Sometimes local does not have what I want, so Amazon it is. I do live out in the middle of Maine, so big city selection is non existent. Bangor has 25K people. That is the biggest "local" I have. Portland, Maine (75K people) is the largest city in Maine and it is 80 miles away.
Sometimes I miss the Seattle area with it's 5 million population and everything is available at any time. Then I wake up...

limp · Oct 2, 2024

Bullitt347 said:
I am all for this.
Unfortunately, there is a majority of people who would rather buy cheap (china/mexico) (walmart) than spend more and buy American made.
Sometimes it is almost impossible to find an American made item.
I went to 5 different Hardware stores in 2 different cities to find a tape measure that was made in the USA. Yes it cost more. Yes I spent a lot of time. To me it was worth it. The urge to just cave and buy from Amazon instead of buying local is real. Most of the time, I buy local. Sometimes local does not have what I want, so Amazon it is. I do live out in the middle of Maine, so big city selection is non existent. Bangor has 25K people. That is the biggest "local" I have. Portland, Maine (75K people) is the largest city in Maine and it is 80 miles away.
Sometimes I miss the Seattle area with it's 5 million population and everything is available at any time. Then I wake up...

What brand Tape Measure was American Made?

RaggedGT · Oct 2, 2024

I mention Walmart one time for buying oil……

85GTStangGuy · Oct 2, 2024

limp said:
What brand Tape Measure was American Made?

I know Milwaukee has a line of "Made in the USA" tools.

Dunno about their tape measures though....

nickyb · Oct 2, 2024

Stanley fatmac measuring tape on amazon # Made in the USA!!!!!!!!!!!

nickyb · Oct 2, 2024

RaggedGT said:
I mention Walmart one time for buying oil……

I buy my oil at Wally world also
Cheap

Mac131 · Oct 3, 2024

Be careful buying things from LMR...here is the Daniel Carpenter thermostat housing I received. The wall thickness at the bends is almost paper thin and weighs about half as much as the OEM housing...both are aluminum.

Here are the 2 plate bolts from the water pump I received from them as well (to be fair it's a motorcraft pump...china made). Notice the heads are way too big and would have dug into the timing cover, preventing the pump from mating properly.

I am going to try and refurbish all my OEM parts...this Chinese garbage is getting frustrating.

Potomus Pete · Oct 3, 2024

I dont know what to think of that POS.

Noobz347 · Oct 3, 2024

We are under no delusions about LMR selling Chinese junk. We just try and avoid it when possible.

I think I have a handle on how I'm going to do it.

Everybody, keep your eyes peeled. You never know where something might appear.

nickyb · Oct 3, 2024

Abra Cadabra
Poof. "Parts you are satisfied with"

5.0-5MT · Oct 3, 2024

Bought the motorcraft TPS from lmr, I believe it was defective out of the box. Made my stang idle at 2k rpm and get stuck there. Paid a shop 375 to fix it, the only issue was the defective TPS.

Noobz347 · Oct 3, 2024

https://stangnet.com/mustang-forums/forums/made-in-america.368/

RANT!!! Fuggin chinees imported crap.

nickyb

I gotta say i never painted my nuts, Never Ever

89ripper

Bullitt347

I have been doing it wrong this whole time

Bullitt347

I have been doing it wrong this whole time

89ripper

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

nickyb

I gotta say i never painted my nuts, Never Ever

nickyb

I gotta say i never painted my nuts, Never Ever

Bullitt347

I have been doing it wrong this whole time

limp

wrap a little cheese around it and its a done

RaggedGT

Been here over a DECADE and still no CT

85GTStangGuy

nickyb

I gotta say i never painted my nuts, Never Ever

nickyb

I gotta say i never painted my nuts, Never Ever

Mac131

Active Member

Potomus Pete

I'm still waiting for the fully nude shots

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

nickyb

I gotta say i never painted my nuts, Never Ever

5.0-5MT

Member

Noobz347

Stangnet Facilities Maint Tech... Er... Janitor

Similar threads

RANT!!! Fuggin chinees imported crap.

I gotta say i never painted my nuts, Never Ever

I have been doing it wrong this whole time

I have been doing it wrong this whole time

Stangnet Facilities Maint Tech... Er... Janitor

I gotta say i never painted my nuts, Never Ever

I gotta say i never painted my nuts, Never Ever

I have been doing it wrong this whole time

wrap a little cheese around it and its a done

Been here over a DECADE and still no CT

I gotta say i never painted my nuts, Never Ever

I gotta say i never painted my nuts, Never Ever

Active Member

I'm still waiting for the fully nude shots

Stangnet Facilities Maint Tech... Er... Janitor

I gotta say i never painted my nuts, Never Ever

Member

Stangnet Facilities Maint Tech... Er... Janitor

Similar threads

Privacy & Transparency

Privacy & Transparency