good part's to get in the 13s

1995 vibrantred · Dec 14, 2004

I have a 1995 mustang Gt 5-speed, with 3.73 gears, exhaust, x-pipe, cold air. What is some good parts to get in low or mid 13s?

DFG 5OH · Dec 14, 2004

Definatly a good Heads/Intake/Cam Combo. Drag Radials, headers, you should see 13s.

super302 · Dec 14, 2004

a good driver

i've seen minor bolt on cars (5spd) get well into 13's, mainly full exhaust, pulleys, gears, good tires, and a GREAT launch

VibrantRedGT · Dec 14, 2004

Got a 13.68 at 101MPH on this stuff.

Edelbrock Performer Intake
BBK 65MM Throttle Body
Pro-M 77MM MAF
Pulleys
MAC equal length headers
Bassani X pipe
MAC cat back
Aluminum driveshaft
Tri Ax shifter
Sticky tires

super302 · Dec 14, 2004

Joe, was that with stock gears?

WhiteDevil · Dec 14, 2004

It ran 13.90 @99mph with 3.73s, Catback, CAI, and an Edelbrock Performer.

rio95 · Dec 14, 2004

You should be pretty close. Check out my sig. If you do H/C/I you should be in the 12's in my opinion, not mid 13's.

Darkhorse845 · Dec 14, 2004

Welcome Aboard!
A great driver is one!

Killercanary · Dec 14, 2004

VibrantRedGT said:
Got a 13.68 at 101MPH on this stuff.

Edelbrock Performer Intake
BBK 65MM Throttle Body
Pro-M 77MM MAF
Pulleys
MAC equal length headers
Bassani X pipe
MAC cat back
Aluminum driveshaft
Tri Ax shifter
Sticky tires

With a VERY similar combo (edelbrock performer intake, 65mm t-body, pulleys, exhaust, 3.73's, nitto DR's) I ran a 13.83 at 98.55mph with a 1.91 60' in my 95 5 speed 'vert. Adding heads, cam, and fuel upgrades have gotten me to where I am now.

1995 vibrantred · Dec 14, 2004

I have not been to a drag strip yet.(because the close one is like 2hr away)
I am 16 years old so not a lot of money left after car payment, so a intake is to much right now. But what kind of pulles to get?

I am new but, rio95 what is H/C/I?

DFG 5OH · Dec 14, 2004

being 16 and wanting to have a fast car sucks!! i'm 17 and and just starting with some little stuff...hopefully i can get a better job, and make more money

final5-0 · Dec 14, 2004

Driving like you don't care if you break it and REAL slicks will put you in the 13's as you are now. Most of us won't push our cars that hard for fear of breaking stuff.

Later
Grady

Killercanary · Dec 14, 2004

H/C/I stands for heads, cam, intake.

ASP pulleys are by far one of the best pulleys you can buy. I have the ASP aluminum pulleys on my car and it was one of the best mods I ever did to my car. They took me from a 14.96 at 91.5mph to a 14.6 at 94.89 with no other changes.

super302 · Dec 14, 2004

another vote for ASP pulleys

slvrbullit302 · Dec 15, 2004

nitrous nitrous nitrous

urban96 · Dec 15, 2004

usuall boltons and intake

VibrantRedGT · Dec 15, 2004

super302 said:
Joe, was that with stock gears?

Oh yea 3:55's. Wish I had 4:10's.

whiteyford0212 · Dec 15, 2004

here buddy this is your ticket

http://musclemustangfastfords.com/tech/0301_MMFFcatch22/

Scott_95GT · Dec 15, 2004

1995 vibrantred said:
I have a 1995 mustang Gt 5-speed, with 3.73 gears, exhaust, x-pipe, cold air. What is some good parts to get in low or mid 13s?

If your car is in good tune (which I'm sure it is) your capable of high 13's right now. With some traction and a good launch, and maybee an intake manifold and some pullies, you are in the mid-13 sec. zone all day.

wytstang · Dec 15, 2004

Traction and a good driver will have you there. Pulleys are great and a short belt too.

good part's to get in the 13s

New Member

Active Member

I'd do anything for free Bapples

"STANGNET'S PENGUIN SMACKER"

I'd do anything for free Bapples

New Member

Member

Banned

The car that set the bar.

New Member

Active Member

Mustang Master

The car that set the bar.

I'd do anything for free Bapples

New Member

bubb rubb says:"woo woooooo"

"STANGNET'S PENGUIN SMACKER"

New Member

New Member

Mustang Master

Similar threads

Privacy & Transparency

Privacy & Transparency