GT-40P'S VS ANY OTHERS

19stang87

New Member

Apr 29, 2003

134

0

0

WoodStock,GA

Apr 16, 2004

#1

• Apr 16, 2004

• #1

ok my ? is wit a set of bare Ps and getting all new springs and bigger valves and everything and to port the heads good....can these heads out perform other big companies outta the box...and would it be cheaper if i was to go this route.. and also wut kinda times could i expect if i was to go the P route..

thanxs

 

tmoss

Gettin Wired

Founding Member

Jun 28, 2001

7,153

32

128

Saint Louis, MO

Apr 16, 2004

#2

• Apr 16, 2004

• #2

Results will depend a great deal on the skill of the head porter. Your gonna pay for that. The P heads are a great street head as-is as they have very strong low-mid lift flow. Just get them milled to give your about 9.5 compression and put good valve train stuff in them.

 

19stang87

New Member

Apr 29, 2003

134

0

0

WoodStock,GA

Apr 16, 2004

#3

• Apr 16, 2004

• #3

and wut kinda results will i have in the ETs and power wise..

 

ONEBADPNY

New Member

Nov 10, 2002

195

0

0

FREMONT, NEBRASKA

Apr 17, 2004

#4

• Apr 17, 2004

• #4

P heads rock my best time is in my sig. they are box stock with better springs. my friend has a few better parts then i do including ported trickflow heads and he runs the same times i do. its funny because my combo is so basic with nothing special.

 

19stang87

New Member

Apr 29, 2003

134

0

0

WoodStock,GA

Apr 17, 2004

#5

• Apr 17, 2004

• #5

ok nice times man...so how much did u pay for them and where did u get them from also........and what could i do to the heads to get them closer to a 11sec run...considering my car ran that same times as u.....

 

ONEBADPNY

New Member

Nov 10, 2002

195

0

0

FREMONT, NEBRASKA

Apr 17, 2004

#6

• Apr 17, 2004

• #6

go to jeff chambers web page. he can do anything to the heads for you. i think they start at around 475 i think. when i get mine ported someday i'm sure i could run 11s. now i don't want to put in a roll bar so i am looking for 12.0s. going to get a dyno tune and chip, skinnies, remove extra weight, and a aluminum driveshaft. go to stangpro.com also and do some reading on the heads. that's what i did.

 

19stang87

New Member

Apr 29, 2003

134

0

0

WoodStock,GA

Apr 17, 2004

#7

• Apr 17, 2004

• #7

do u have a link to his site maybe?? thanxs

 

ONEBADPNY

New Member

Nov 10, 2002

195

0

0

FREMONT, NEBRASKA

Apr 17, 2004

#8

• Apr 17, 2004

• #8

http://home.neo.rr.com/chambersracing/

go under for sale then gt-40p. i have emailed him before very nice to talk to

 

LDiablo

New Member

Sep 24, 2003

53

0

0

Apr 17, 2004

#9

• Apr 17, 2004

• #9

Just a heads up on the GT40P's. I bought mine on E-Bay. Brand spankin' new with valves & springs, and they've never been bolted on a motor for $467 shipped to my door. Here's a link:
http://cgi.ebay.com/ebaymotors/ws/e...&category=33617&sspagename=STRK:MEBWN:IT&rd=1
You may wanna give him a call if you're looking to get a stock set for now,then move on to get them ported later on. That's my situation at the moment.