• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Having problem with heating after changing heater core

  • Thread starter Thread starter PeteyAce
  • Start date Start date Mar 5, 2007

PeteyAce

Member
Jul 2, 2004
346
0
17
Mar 5, 2007
#1
  • Mar 5, 2007
  • #1
I had a few threads but no luck, evers since my heater core went ive been having problems with my heat and temperature, whenever i turn the heat on my temperature goes up a considerable amount, also the fan switch for my heating console gets so hot that when it is on for long periods at a time (20mins maybe) it actaully starts to smoke and melted a bit by the back of the harness where it plugs into the switch. and other thing i noticed when i turn on the heat is that it sucks alot of juice out of my battery. Ive burped the system numerous times but nothing, those are my symptoms, this is my problem, any suggestions?
 

04sleeper

Founding Member
Jun 22, 2002
2,674
14
89
Dallas, TX
Mar 5, 2007
#2
  • Mar 5, 2007
  • #2
Sounds like a wiring issue or fan motor issue in the dash.

Either way it looks like you will have to pull it apart again to check things out.
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Mar 5, 2007
#3
  • Mar 5, 2007
  • #3
Sounds like your heater blower fan motor is frozen or binding, causing excessive current draw. You will need to replace the heater fan switch, connector, terminals, fan motor, and possibly the fan motor connector and terminals as well. When heater cores fail, they usually fill the heater case with water/coolant. It's not hard to se how the motor might get all rusted and refuse to function properly.
 

PeteyAce

Member
Jul 2, 2004
346
0
17
Mar 5, 2007
#4
  • Mar 5, 2007
  • #4
i was thinking my motor, but the fan switch still functions properly, just a little warped, where is the exact location of the motor?
 
S

superhuaman

New Member
Nov 8, 2004
907
0
0
Harrisburg, PA
Mar 5, 2007
#5
  • Mar 5, 2007
  • #5
under the dash on the passenger side, towards the kick panel
 
You must log in or register to reply here.

Similar threads

M
Idle control problems
  • miser143
  • Aug 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
214
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 29, 2026
DadLife0724
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
249
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
K
Console Heat after MGW shifter install
  • KirkACola
  • Sep 24, 2025
  • 2010 - 2014 Specific Tech
Replies
13
Views
819
2010 - 2014 Specific Tech Sep 24, 2025
Noobz347
A
Resolved 302 still running after turning off ignition
  • AlexM556
  • Nov 14, 2026
  • Classic Mustang Specific Tech
Replies
4
Views
119
Classic Mustang Specific Tech Nov 15, 2026
AlexM556
A
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
756
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?