• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

hello

  • Thread starter Thread starter jdschreier
  • Start date Start date Oct 3, 2005
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#1
  • Oct 3, 2005
  • #1
hi,im new to this forum,but not to mustangs

i just got my brothers 1990 5.0 lx,and shes a beauty,but i am having a few issues of which i cannot figure out,im hoping someone here will be able to assist me.

first off i took my car to emissions the other day *sigh,i hate maryland*,and even after extensive work to the emissions system (new cats,smog pump,etc.) i still failed in hydrocarbons (1.400limit and i got 1.427).so it wasnt by much.anyways,i wasnt surprised because its been in florida all its life and my bro ripped all the emissions stuff out,so looking over the engine bay and noticed this



would this affect my emissions in any ways?and how would i go about fixing it properly?

i hope you guys can help me,thanks

jeremy

p.s. i used search but couldnt find what i was looking for
 

Attachments

  • 30Sept005.webp
    38.6 KB · Views: 94

sunil6784

Member
Mar 31, 2005
620
0
18
Boston, MA
Oct 3, 2005
#2
  • Oct 3, 2005
  • #2
How old are the 02's on the car?
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#3
  • Oct 3, 2005
  • #3
2 years according to my brother,he did manage to keep a detailed record of everything he did/bought for the car.
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Oct 3, 2005
#4
  • Oct 3, 2005
  • #4
That allows exhaust gases to flow out of the cylinder heads and then either be recirculated back into the engine or sent out the exhaust. Yes, it will indeed affect the emmisions. Try a salvage yard to get the replacement parts and then go see the tailpipe police.
 

woodyy24

New Member
Mar 30, 2005
290
0
0
illinois
Oct 3, 2005
#5
  • Oct 3, 2005
  • #5
yeah, sure would. its used to pump air into your exhaust making it burn the excess hydrocarbons on your cats. it needs to be hooked up to your air pump.
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#6
  • Oct 3, 2005
  • #6
where does it connect to,the outlet pipe from the smog pum to the cats?
 

woodyy24

New Member
Mar 30, 2005
290
0
0
illinois
Oct 3, 2005
#7
  • Oct 3, 2005
  • #7
couldnt tell ya where exactly. i dont need any emissions crap on my cars. but i do know it hooks up to an outlet on the pump.
 

crazypete

All my crevices are greased.
Oct 22, 2004
930
4
18
Arlington, MA
Oct 3, 2005
#8
  • Oct 3, 2005
  • #8
ss93cobra said:
That allows exhaust gases to flow out of the cylinder heads and then either be recirculated back into the engine or sent out the exhaust. Yes, it will indeed affect the emmisions. Try a salvage yard to get the replacement parts and then go see the tailpipe police.
Click to expand...

Actually that is part of the AIR injection system that sends air from the smogpump directly to the exhaust ports. That tube is the end of the injection pipe. There should be a bypass and a selector, both vacuum driven hooked up to the tab/tad solenoids.

It has nothing to do with recirculation. The EGR solenoid on the back of the throttle body takes care of that via passages in the heads and intake.

I see the second tube, the air injection tube that runs to the cats, still in place. Technically, if the car is at operating temperature, it would inject the air to this second tube anyway. All you are really losing is some added emissions control when the car is in warmup, when it diverts air to the exhaust ports directly.

You know....you could hook up a hose to that tube and dump some exhaust into your fender if you somehow get that one way drum off the end. That would lower your hydrocarbon emissions a bunch.
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#9
  • Oct 3, 2005
  • #9
thanks for the info,i think this may be biigger than i though,i forgot to mention that there are two vaccume lines capped and dangling,i think they connect to that as well.

right?wrong?
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
Oct 3, 2005
#10
  • Oct 3, 2005
  • #10
That tube goes to the back of each head and is part of the smog system. There is a hose that comes off of the smog pump and the H pipe to a valve that then feeds into that tube. If that is disconnected that will probably add to the problem. Your cats can also be shot which isn't all that uncommon for a 20 year old car.
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#11
  • Oct 3, 2005
  • #11
stated in first post,brand new cats,smog pump,exhaust(even thought that has nothing to do with emission) etc.

will getting a "T" fitting and branching a hose to that tube solve the problem?
 

DTT92LX

New Member
Oct 28, 2003
185
1
0
Downingtown, PA
Oct 3, 2005
#12
  • Oct 3, 2005
  • #12
You circled the check valve on the line from the smog pump to the heads. Below it you can see the check valve to the cats. The path is from pump to vac operated valve to another vac operated diverter valve. The diverter valve routes air (not exhaust) to either the tube going to the heads (which you circled) or the tube going down to the cats.

From the pic it looks like check valve for the cats has a hose on it. Where is that connected to? Should be connected to the diverter valve. And if it is connected there, what is the other port on that valve connected to? It should be connect with a hose going to the heads check valve (circled in pic).

The black and white vac tubes that go off to the right in your pic will lead you to the 2 vac operated valves I'm referring to.

G'luck

EDIT: Guess I took too long to write this up! WHAT THEY SAID
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#13
  • Oct 3, 2005
  • #13
well,im guessing theres supposed to be a valve between the smog pump and the tube to the cats....there isnt one

im so lost,lol

anyone got parts # or any odea where i can order them from?

then im going to go punch the mechanic that told me that the hose was all it neededfor the emission system to work
 

DTT92LX

New Member
Oct 28, 2003
185
1
0
Downingtown, PA
Oct 3, 2005
#14
  • Oct 3, 2005
  • #14
Don't be lost. It's easy...

-Smog pump
-hose to vac valve
-hose from val valve to vac diverter valve
-1 hose from diverter valve to heads check valve (circled in pic)
-Other hose from diverter valve to cat check valve (already hooked up)
-finally, vac hoses (black and white in pic) go to the 2 vac valves mentioned.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 3, 2005
#15
  • Oct 3, 2005
  • #15
The smog pump has two vacuum operated valves. The first valve either dumps the pump output to the open air or directs it to the next valve. The smog pump dumps its output at full throttle to save horsepower. The second valve directs the air to either the passages in the heads or to the tube that runs to the cat converters. Both the tube for the head and the tube going to the cat converters have one way check valves to prevent the hot exhaust gas from backing up into the tube and the control valves.

See http://www.veryuseful.com/mustang/tech/engine/images/88Stang5.0Vacuum.gif for smog pump vacuum line help

Here are some of the codes generated by faulty parts in the smog pump system and their fixes...

Codes 94 & 44 - Check vacuum lines for leaks, & cracks. Disconnect the big hose from smog pump: with the engine running you should feel air output. Reconnect the smog pump hose & apply vacuum to the first vacuum controlled valve: Its purpose is to either dump the pump's output to the atmosphere or pass it to the next valve. The next vacuum controlled valve directs the air to either the cylinder heads when the engine is cold or to the catalytic converter when the engine is warm. Disconnect the big hoses from the back side of the vacuum controlled valve and start the engine. Apply vacuum to the valve and see if the airflow changes from one hose to the next.

The two electrical controlled vacuum valves mounted on the rear of the passenger side wheelwell turn the vacuum on & off under computer control. Check to see that both valves have +12 volts on the red wire. Then ground the white/red wire and the first solenoid should open and pass vacuum. Do the same thing to the light green/black wire on the second solenoid and it should open and pass vacuum.

Remember that the computer does not source power for any actuator or relay, but provides the ground necessary to complete the circuit. That means one side of the circuit will always be hot, and the other side will go to ground or below 1 volt as the computer switches on that circuit.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host)

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Code 81 – Secondary Air Injection Diverter Solenoid failure AM2. The secondary air diverter solenoid valve isn’t working on the Thermactor Air System (smog pump). Look for broken or missing vacuum lines on the solenoid valve to the diverter valve. The solenoid valve is located on the back side of the passenger side wheel well. Check the solenoid valve for +12 volts at the Red wire and look for the Lt Green/Black wire to switch from +12 volts to 1 volt or less. The computer controls the valve by providing a ground path on the LT Green/Black wire for the solenoid valve.

Code 82 – Secondary Air Injection Diverter Solenoid failure AM1. The dump valve air diverter solenoid valve isn’t working on the Thermactor Air System (smog pump). Look for broken or missing vacuum lines on the solenoid valve to the diverter valve Check the solenoid valve for +12 volts at the Red wire and look for the Red/White wire to switch from +12 volts to 1 volt or less. The computer controls the valve by providing a ground path on the Red/White wire for the solenoid valve.

Putting the computer into self test mode will cause all the actuators to toggle. This can be done either with a jumper wire or code scanner.

How to pass emissions testing:

1.) Make sure all the emissions gear the car was made with is present and connected up properly. That includes a working smog pump and cats.

2.) Make sure that you have fresh tune up with spark plugs, plug wires, cap, rotor, fuel & air filters. An oil & filter change is a good idea while you are at it.

3.) Dump the codes and see what the computer says is wrong…

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.mustangworks.com/article...c-iv_codes.html

IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/det...iption.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $33.

4.) Post the codes and get help to fix them. Don’t try to pass with codes not fixed. Clearing the computer just temporarily removes them from memory, it doesn’t fix the problem that caused the code to be set.

5.) Be sure to do the testing on a hot engine. Drive for 15-20 minutes prior to taking the test to get operating temps up into the normal range. Do not shut off the engine while waiting for your turn on the test machine. An engine up to full operating temperature puts out fewer emissions.
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#16
  • Oct 3, 2005
  • #16
those valves are not there,i need to order them,any good site recommendations?

i'll prolly order them friday if i can find them
 

crazypete

All my crevices are greased.
Oct 22, 2004
930
4
18
Arlington, MA
Oct 3, 2005
#17
  • Oct 3, 2005
  • #17
jdschreier said:
those valves are not there,i need to order them,any good site recommendations?

i'll prolly order them friday if i can find them
Click to expand...

Ignore them. They are unnecessary strictly for the purpose of passing emissions. The IDEAL setup is the following: run the thick hose to that blocked off checkvalve. This injects air at the earliest point in the system.

You dont need a bypass, it keeps the extra air from backfiring the exhaust on engine braking. But the exhuast usually doesnt backfire at all. Hook it up and try it. It's free.

The diverter that selects between the cat AIR tube and the exhuast port tube is used to differentiate between warmup cycle(exhuast port tube, the blocked off one) and and regular operation (cat tube).

But selecting the cat tube gives the spent gasses less time to burn and dumping the air removes the airpump's effects so you can see it is pointless to actually buy those switches and clutter up the enginebay. Hook the airpump directly to the blocked off tube and plug the lower tube and you're good to go.
 
J

jdschreier

New Member
May 19, 2005
8
0
0
annapolis,md
Oct 3, 2005
#18
  • Oct 3, 2005
  • #18
well,i just ran the treadmill again after swapping the hose

new results:

hc 1.0315, state req 1.4000
co 2.5518, state req 30.000
NOx 0.8690, state req 2.5000

overall : pass

thanks you guys,i really appreciate the help (and the saved money)
 

crazypete

All my crevices are greased.
Oct 22, 2004
930
4
18
Arlington, MA
Oct 3, 2005
#19
  • Oct 3, 2005
  • #19
Hooowa!

Who da man ?
 
You must log in or register to reply here.

Similar threads

5
Hello Everyone !
  • 5150K
  • Jul 3, 2026
  • The Welcome Wagon
Replies
0
Views
186
The Welcome Wagon Jul 3, 2026
5150K
5
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
E
Finished my Fox Hydroboost Install - Tips
  • Engineer Duane
  • Apr 9, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2025
Engineer Duane
E
What in gods green earth happend to my N/A 2.3?
  • Piranahbite
  • Mar 24, 2024
  • 2.3L (N/A & Turbo) Tech
Replies
8
Views
2K
2.3L (N/A & Turbo) Tech Jun 1, 2024
Piranahbite
rebuilt heater box, weak heat
  • connella08
  • Jan 10, 2023
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
2K
1965 - 1973 Classic Mustangs -General/Talk- Jan 10, 2023
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?