• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Help with problems on first startup after h/c

  • Thread starter Thread starter TrueBlue95GT
  • Start date Start date Jun 20, 2006

TrueBlue95GT

Member
Sep 29, 2003
966
0
16
Connecticut
Jun 20, 2006
#1
  • Jun 20, 2006
  • #1
I've got a friend with a 92 GT that just got done putting y302 heads on with an e-cam...I got the timing relative and it fired up, but it doesn't idle and it sounds like either a really loud exhaust leak or metal pieces slapping each other. I don't think it's the exhaust leak because the same headers were used before with no problems...what could be happenning and what should we check for? By the way, I thought that it could be that the stock rockers weren't adjusted right and that with this combo, the pushrods may need to be a different length.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 20, 2006
#2
  • Jun 20, 2006
  • #2
Did you check pushrod length when checking geometry of the valve train? How much preload did you put on the rockers?
 

TrueBlue95GT

Member
Sep 29, 2003
966
0
16
Connecticut
Jun 20, 2006
#3
  • Jun 20, 2006
  • #3
Well he did it while I wasn't there, but I think he thought he didn't need to do it since it was the stock size pushrods and the stock rockers and y302's...Is it right that he thought that?
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jun 20, 2006
#4
  • Jun 20, 2006
  • #4
Only way to tell is measure, or atleast color in the valve tip with a sharpie, set up one set of rockers, turn the motor over and then check the wear pattern on the valve tip. it should be centered, and no wider then .080" if it is off center towards the header the PR is too long, if it is towards the intake they are too short. You also want to make sure the roller tip first moves towards the header side, then towards the intake. I assume these are ped mount so you can also play with the shims to get the preload correct.
 
You must log in or register to reply here.

Similar threads

M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
862
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
C
Engine Cylinder 5,,7, & 8 run significantly cooler than the other cylinders
  • Crisfixes
  • Sep 27, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
317
Fox 5.0 Mustang Tech Sep 27, 2025
Noobz347
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
628
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
918
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
Resolved Fixing a GT40P Valvetrain nightmare
  • foxbodyclark
  • May 21, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
1K
Fox 5.0 Mustang Tech May 24, 2025
limp
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?