• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

horn problem

  • Thread starter Thread starter xexitenglishx
  • Start date Start date Oct 10, 2005
X

xexitenglishx

Member
Jun 27, 2004
153
0
16
Oct 10, 2005
#1
  • Oct 10, 2005
  • #1
Ok a few days ago my horn started to go off on its own. I didnt know this at the time and it had actually killed my battery. I jumped the car and didnt hvae a problem. When i honked the horn th wouldnt stop honking. Then the fuse blew. I put a new fuse in and it blew right away. I have a ford manual and it says to check the horn. I did that using a direct battery hookup to the horn. I couldnt get it to honk but i could get the wire to heat up very nicely. Would a blown horn cause the fuse to blow everytime now that the horn is honked? I checked teh connectiosn at teh steering wheel and they are working. I even checked the connection at the column by trying to short the horn to honk in the connection at teh steering column. No luck it just blew the fuse again. Anyone have any other input before i go out and buy another horn? thanks for your help.
 

Zero_chance

Founding Member
May 29, 2001
1,244
7
59
Maricopa, AZ
Oct 11, 2005
#2
  • Oct 11, 2005
  • #2
Its actually pretty common for moisture to build up and cause the contacts to stick in our horns. Mine did it and I just relocated the horn to a button nearby. You may have heated up a wire and caused it to short out so now every time the horn tries to power up it blows the fuse.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 11, 2005
#3
  • Oct 11, 2005
  • #3
The horns typically develop an internal short to ground, which causes the fues to blow.

The horns are located under the car on the driver's side, forward of the front wheel well. Disconnect BOTH horns, replace the fuse: if the fuse blows immediately, the problem is most likely in the cigar lighter circuit. If not, then press the horn button on the steering wheel: if the fuse blows the problem is in the wiring between the horn relay and the horn. If doesn't blow when you press the horn button, connect ONE of the horns and try again. If it still doesn't blow the fuse, connect the other horn. Chances are that the first horn you re-connect will blow the fuse. Whatever horn blows the fuse at this point has an internal short and is trash. Time for a trip to the junkyard...
 
X

xexitenglishx

Member
Jun 27, 2004
153
0
16
Oct 11, 2005
#4
  • Oct 11, 2005
  • #4
Ok thanks alot. I will do this testing over the weekend because i am at school now. I know its not the steering wheel bc i have tried to activate it furtehr down the line. Now i must disconnect the horns. If i disconnect one do i have to connect the hot line or are both the connection hot. I other words are tehy dais chained or they bothhave a hot line running to them? Thanks
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Oct 12, 2005
#5
  • Oct 12, 2005
  • #5
TMoss has some good diagrams at that veryuseful.com site.. I'm sure you'll find what you're looking for there.
 
W

wazazzle

New Member
Mar 30, 2005
618
1
0
In the dumpster behind McDonalds. WA
Oct 12, 2005
#6
  • Oct 12, 2005
  • #6
i had the same problem. horn testED fine, but whenever i hit the horn it always blew my fuse. i took off my fender and replaced both horns ($12x2=$24 total) hooked up both horns and it works awesome now. no more fear of driving without a honker! i got a high freq and low freq horn so everyone can hear me. its hella LOUDDDD!!!
 
W

wazazzle

New Member
Mar 30, 2005
618
1
0
In the dumpster behind McDonalds. WA
Oct 12, 2005
#7
  • Oct 12, 2005
  • #7
prob with pg, same submit
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 12, 2005
#8
  • Oct 12, 2005
  • #8
xexitenglishx said:
Ok thanks alot. I will do this testing over the weekend because i am at school now. I know its not the steering wheel bc i have tried to activate it furtehr down the line. Now i must disconnect the horns. If i disconnect one do i have to connect the hot line or are both the connection hot. I other words are tehy dais chained or they bothhave a hot line running to them? Thanks
Click to expand...
Only one wire per horn. They ground the metal horn shell to the body.
 
8

89stangWhiz

Member
Sep 28, 2005
104
0
16
Mechanicsville, MD
Oct 12, 2005
#9
  • Oct 12, 2005
  • #9
as was mentioned mine were basically glued together as the fabric between the 'plates' wore down. Take the button totally apart and you can see it. I am in the process now of getting new material to put in between the plates and she should be as good as new. In the meanwhile I was finally able to get another button for her
 
You must log in or register to reply here.

Similar threads

H
70 fastback: Good battery, but nothing happens.
  • hankmeister
  • Mar 4, 2024
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
12
Views
2K
1965 - 1973 Classic Mustangs -General/Talk- Mar 21, 2024
hankmeister
H
B
SN94 5.0L
  • BenSN94
  • Jun 30, 2024
  • 1994 - 1995 Specific Tech
Replies
1
Views
692
1994 - 1995 Specific Tech Jul 1, 2024
General karthief
A
Resolved 03 GT Parasitic Draw Fuse 26 (PCM)
  • Antrix
  • Mar 22, 2025
  • SN95 4.6L Mustang Tech
Replies
2
Views
864
SN95 4.6L Mustang Tech Mar 24, 2025
89ripper
J
Help! 78 II has no power to any electrical except headlights and taillights and hazards.
  • JackH
  • Jan 8, 2024
  • 1974 - 1978 Mustang II Talk & Tech
  • 3 4 5
Replies
93
Views
14K
1974 - 1978 Mustang II Talk & Tech Mar 28, 2024
Noobz347
M
Resolved PATS problem with a Mustang 2010 V6 - SOLVED-
  • MRMRacing
  • Feb 22, 2025
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
7
Views
5K
2005 - 2014 S-197 Mustang -General/Talk- Mar 1, 2025
MRMRacing
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?