How Do I Use Lightning Maf Meter?

[walker95svt]

Hey guys. I want to buy a lightning 90mm maf and 42# injector combo, because they're so cheap. I know people run them on our cars, but somebody's gotta know EXACTLY what it takes. How do I do it?

setup:
95 cobra, computer unmodified except for chip

 

[final5-0]

You gotta use a tuning interface like PMS, Tweecer, or get a chip.

Grady

 

[blksn955.o]

I also believe you need a new MAF harness/pigtail deal to splice the connector to the stock harness. The newer cars have a diff. connection.

This part is like 15-20$

 

[walker95svt]

I read your post on the other MAF page, final50. It should work fine to get it to my tuner though, right? At least that's what I gathered. As far as the pigtail, anyone know where I can get one?

 

[OinkAodeOink]

I would like to know the same, I plan on going with the Lightning mass air meter and injectors, on my 01 GT.. I just need the car to be drivable to the tuners 15 miles down the road.

 

[Don 95Vert]

For a '95 you need the MAF, a chip or tuner, a silicon adapter to adapt the 4" MAF to your powerpipe, a MAF adapter for the filter and a 4" cone style filter and finally a late model MAF harness.

We sell the chips, harnesses, MAF adapters - or use a TwEECer - Jegs or Summit has the Filters, Hose Techniques will have the hose adapters - and sometimes you can make a Home Depot rubber plumbing adapter work too.

Usually the car need to be on a dyno or at least have a wide band attached, because as good as these MAFs are, they can't compensate for different inlet tracts. And 'base' tunes are usually not good enough.
Don

 

[blksn955.o]

for the MAF connector check out this link

http://eectuning.org/forums/viewtopic.php?t=3418

 

[walker95svt]

but, me and oink still need to know if it's safe to drive our vehicles without the tune on. It'll still work, but not perfectly, right? My tuner's three hours away. I don't know about all the other stuff you suggested. I need it to work with my NOVI 2000 kit. The kit is more for stock cars, and doesn't have injectors or anything. It came with an FMU. My car has a boost ready 331, and I want the bigger injectors.

 

[blksn955.o]

You may have to run some kind of FMU (I know they suck) on the stock MAF/inj. with the smallest boost wise pullie you can find and turn your timing way way down. Then install the MAF connector and inj. un-install the FMU when you get to the dyno...otherwise do all the installs and trailer it to the dyno. I would install everything and trailer it 3hrs is a long haul to take with an un-tuned combo without a trailer anyway...

 

[KBCobra95]

Would the 90mm fit to a JLT Intake? It is 4" tube.

 

[Don 95Vert]

It probably won't even run at all without a chip. If it does start and run (some do) bring along a new set of plugs to install at the dyno. If it seems to run semi-OK (very rare) then it's OK to drive it there, but stay out of it... See if your tuner will mail you a chip to get you there - I do that for people all the time. It still may not run so great, but it'll get you there.

 

[greenlantern]

Here's the adapter

http://cgi.ebay.com/ebaymotors/ws/e...bay.com:80/?from=R40&satitle=8007505235&fvi=1



http://www.musclemotors.com/index.asp?PageAction=VIEWPROD&ProdID=1066&HS=1

 

[KBCobra95]

I bought a new pigtail from ford, but the one I got has 6 wires instead of 4? It is the newer connection for the 90 mm lightning. whats the dealio?

 

[Don 95Vert]

The two outer wires on each side are for the ACT which in later cars is in the MAF - so you can clip those off.

 

[KBCobra95]

Thank you so very much sir!

 

[KBCobra95]

Wait! I have one more question. All the wires are white! Which one goes where? Or do I just line up with old ones. Thanks again!

 

[Starman]

the wires stay lined up

 

[Don 95Vert]

That will get it wired backwards - because the later connector is "flipped" vs. the old connector. Starting from the far left hand side (assuming you clipped the two outer wires) with the lock part of the connector on top, looking down at it, with the wires going away from you and the connector facing you the wires should be:

| Red | Black | Blue-red stripe | dark blue-red stripe |

Solder the red to the red and then just do the rest in order - use shrink wrap too.

 

[BlackVert]

Wait! I have one more question. All the wires are white! Which one goes where? Or do I just line up with old ones. Thanks again!

subscribing ... post a pic of it when you are done, ok? pics = :Word:

 

[KBCobra95]

That will get it wired backwards - because the later connector is "flipped" vs. the old connector. Starting from the far left hand side (assuming you clipped the two outer wires) with the lock part of the connector on top, looking down at it, with the wires going away from you and the connector facing you the wires should be:

| Red | Black | Blue-red stripe | dark blue-red stripe |

Solder the red to the red and then just do the rest in order - use shrink wrap too.