• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Im going to attemp it..

  • Thread starter Thread starter 87foxstang
  • Start date Start date Dec 5, 2007

87foxstang

Member
May 10, 2007
0
0
16
Cromwell, CT
Dec 5, 2007
#1
  • Dec 5, 2007
  • #1
Well since my car has been doing the one wheel peel, i figured this winter would be the perfect time to do the trac lock rebuild. I searched and heard some people say its hard and some said its not to bad. Now i have a decent amount of mechanical knowledge and many special tools, like verniers and all kinds of things i got from my dad.

Should I attempt this, I feel if i have some directions and the right parts I should be good.

Also, i heard you need a special tool, but what is that tool

Any input appreciated, thanks guys
 
F

facemelter71

New Member
May 29, 2006
60
0
0
cincy
Dec 6, 2007
#2
  • Dec 6, 2007
  • #2
-jackstands
-remove wheels
-remove drums(or disc)
-Pull diff cover
-drain stank ass fluid
-take 5/16 bolt out that holds the cross pin in.
-remove croos pin
-push axles in toward center of car
-remove c-clips from axles ends
-pull axles out and inspect for bearing wear at end near lug flange
-remove 4 bolts on the u-shaped carrier's on either end of the diff.
-keep bolts and spacers..SPECIFIC TO SIDE.(left to left and right to right)
Some one take it from there.
Or head to junk yard and find 87-88 turbocoupe rearend and replace your with it.Comes with fords limited slip (manual 3:55 Auto 3:73)and rear disc brakes.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Dec 6, 2007
#3
  • Dec 6, 2007
  • #3
job is not hard at all... just make sure you keep your clutches and steels in the right order, some like to lube clutches but I feel it makes life harder than it should its all personal preference really. The hardest part of the whole job is getting the S spring back in and you will find thats not that hard either. Good luck!!!!!!!!
 
I

iapexl8r

Member
Apr 1, 2005
254
0
17
Dec 6, 2007
#4
  • Dec 6, 2007
  • #4
its easy I say go for it. If you remove the carrier from the housing be sure the shims go back in the same location (right side/ left side). I have herd of a few people who dont remove the carrier assy to do the rebuild but have never tried it.
the stock fiberdisc/steeldisc configuration can be modified to increase capacity. I have done this it is easy and effective. the revised clutch packing sequence is (from side gears out) friction disc, steele,friction disc,steel,friction disc, steel,friction disc then the shim. This gives you four friction discs per side instead of three. Be sure to soak the friction discs in friction modifier fo 20 mins or so.

Chris
 

87foxstang

Member
May 10, 2007
0
0
16
Cromwell, CT
Dec 6, 2007
#5
  • Dec 6, 2007
  • #5
cool, thanks alot guys, sounds like i could do it ok. Once i start it later on this winter, if i have anymore questions, ill be asking. But i read over some previous posts about it and i seemed to get the gist of it. Thanks dudes
 

SuperStang83

Founding Member
Mar 21, 2001
1,693
0
49
Boyertown, Pa
Dec 6, 2007
#6
  • Dec 6, 2007
  • #6
I've never done it, but I have heard that it is easy. Good luck.
 
You must log in or register to reply here.

Similar threads

H
Drivetrain 4R70W clutch friction/metals/piston set up questions for transmission guru
  • Hizdudeness
  • Apr 4, 2024
  • Fox 5.0 Mustang Tech
Replies
2
Views
1K
Fox 5.0 Mustang Tech Nov 15, 2024
slow84lx
S
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
WTB/Trade Looking for a T-Top Hatch. Possible convertible trade? (Rhode Island)
  • 7upper
  • Mar 18, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
412
Fox Body Mustangs For Sale (1979-93) Mar 18, 2025
7upper
H
Engine 2004 gt engine swap
  • H12
  • Feb 14, 2024
  • SN95 4.6L Mustang Tech
Replies
8
Views
4K
SN95 4.6L Mustang Tech Feb 16, 2024
Yel2002GTAuto
Y
E
Finished my Fox Hydroboost Install - Tips
  • Engineer Duane
  • Apr 9, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2025
Engineer Duane
E
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?