• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

injector tuning?

  • Thread starter Thread starter btlfed91
  • Start date Start date May 1, 2008
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
May 1, 2008
#1
  • May 1, 2008
  • #1
If you go from 19 to 24 lb injectors do you have to tune the computer to the 24's all i knew to do was swap out the tube inside the MAF tube to the right size for 24's but someone else told me that I actually have to tune the computer to give a different pulse width with the 24's.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 2, 2008
#2
  • May 2, 2008
  • #2
You have 2 basice options...

1. Trick the ecu, but swapping out the MAF meter to compensate for the larger injector size.

2. Get a J3 chip and custom tune for the larger injectors.


Personally, I feel the J3 chip is worth the effort, even if no other changes have been made.
But, if the plans for the car are relatively mild, then the cost/time needed for a custom J3 chip may not be worth it considering there is little room for improvement via the tune...

In other words...
Recalibrating the MAF may be cheaper, but won't be better than a custom tune.

Are you using a C&L meter?

jason
 
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
May 2, 2008
#3
  • May 2, 2008
  • #3
yeah it's a 76mm C&L meter and the inside tube is for 24's do I need to do anything else
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 2, 2008
#4
  • May 2, 2008
  • #4
btlfed91 said:
yeah it's a 76mm C&L meter and the inside tube is for 24's do I need to do anything else
Click to expand...
You shouldn't need to do anything else... but see how it drives...

C&L has a kinda weird reputation though...
 
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
May 2, 2008
#5
  • May 2, 2008
  • #5
well thats my thing it drives like crap its got several problems that have been going on since I did my H/C/I swap I went with a TFS setup and went with the 24's just to be on the safe side I've got good fuel pressure and I thought I covered all the bases but it idles horribly...up and down,up and down, then it will die after a few minutes of that and then I put a cage in it and now for some reason if I push in the clutch to fast it will die its got a loud whistle that goes with the idle surge that sounds like it is coming from the back of the engine compartment but cant find a vacuum leak anywhere.Ive been working on it for weeks and cant figure it out so I took it to a buddies shop and he couldnt figure it out eather so he called trick flow and summit tech support and they said that I might need to go back to my 19 lb injectors. Im lost!
 

mustangfan1990

New Member
Jul 17, 2005
505
1
0
Lenoir, North Carolina
May 2, 2008
#6
  • May 2, 2008
  • #6
btlfed91 said:
well thats my thing it drives like crap its got several problems that have been going on since I did my H/C/I swap I went with a TFS setup and went with the 24's just to be on the safe side I've got good fuel pressure and I thought I covered all the bases but it idles horribly...up and down,up and down, then it will die after a few minutes of that and then I put a cage in it and now for some reason if I push in the clutch to fast it will die its got a loud whistle that goes with the idle surge that sounds like it is coming from the back of the engine compartment but cant find a vacuum leak anywhere.Ive been working on it for weeks and cant figure it out so I took it to a buddies shop and he couldnt figure it out eather so he called trick flow and summit tech support and they said that I might need to go back to my 19 lb injectors. Im lost!
Click to expand...

Sounds like you do have a vaccumm leak. If it hasnt ran right since the HCI swap and you have the MAF sensor for 24s then I doubt it is the MAF. you might need to clock your MAF sensor (turning it till the idle smooths out) or if you have a vaccumm leak more than likely it will run lean and idle high. I would check around all the upper and lower gaskets for leaks. You could have a internal leak may be why you cant find it. When you try to drive it what do it do? and what do you fuel pressure do?
 
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
May 2, 2008
#7
  • May 2, 2008
  • #7
for the most part when I drive it it runs like a bat out of hell but for some reason since we did the cage now it is backfiring like it is out of time or something but the timing is dead on.I dont have a guage that I can watch while I'm driving and I havent tried it on a dyno.also we tried carb cleaner,propane,and smoke all around the upper and lower and all around the back of the engine and couldnt find anything.what will cause an internal vacuum leak? having a valve to tight can cant it,thanx for the help guys Im ready to sell this damn car!
 

mustangfan1990

New Member
Jul 17, 2005
505
1
0
Lenoir, North Carolina
May 2, 2008
#8
  • May 2, 2008
  • #8
Valve too tight would keep it open all the time and would make it run like **** on that cylinder. AN internal leak would be a broken gasket in the valley somewhere where your lower meets your heads. I am thinking that you have a gasket problem somewhere. When you put your cam in did you make sure your cam and crank gears were lined up PERFECT and that your motor was at TDC. If not then doesnt matter what your Distriubtor says cause you will be wrong no matter what! Also did you torque your head bolts down tight to the right specs. Go back over everything you done to the car since it last run right and make sure you did everything by the book. Did you cut any corners or did you hit any snags along the way that you might have thought you fixed but maybe not?
 
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
May 2, 2008
#9
  • May 2, 2008
  • #9
I made sure I payed really close attention when I did everything because I didnt want to go back and do this I am 100% sure the gears are lined up right everything was torqued right but I guess it is always possible that I could have a gasket problem somewhere but shouldnt I still be able to find it with the carb cleaner or propane and where would my whining noise be coming from also I am very meticulous with this stuff like I said because I didnt want to do it again so I didnt take any shortcuts
 
E

eickholt78

New Member
Aug 9, 2007
9
0
0
May 3, 2008
#10
  • May 3, 2008
  • #10
i have 24's and my pressure is at 42 with the hose on, as far as the idle surge, ford made this kit for the iac that mounts between it and the iac p/n is f2pz-9f939-a, i run this on all my stangs with bigger cams and injectors. i also have a c&l 76mm mass air and it idles perfectly with 24's and an x-cam. as far as the whining goes, are you sure the pcv or the spot it sits in on the intake isnt plugged? what about the vaccum tree for the booster and the other ports? maybe it is cracked.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 3, 2008
#11
  • May 3, 2008
  • #11
eickholt78 said:
i have 24's and my pressure is at 42 with the hose on, ...
Click to expand...
Fuel pressure should be set with the vac line disconnected


btlfed91 said:
but I guess it is always possible that I could have a gasket problem somewhere but shouldnt I still be able to find it with the carb cleaner or propane
Click to expand...
I've had a vac leak common to intake runner of #1 and the lifter valley.
The lower intake/head gasket had slipped down when I lowered the intake into place.

Are you getting any Diagnostic Codes?
Did you install the stock Sensor in the C&L?
Have you verified the diameter of the SAMPLE tube in the C&L?
 
E

eickholt78

New Member
Aug 9, 2007
9
0
0
May 3, 2008
#12
  • May 3, 2008
  • #12
yeah i know you set pressure with the line off, alls i am saying is when i hook the line up it is at 42 pounds, so with the line off i am at about 48
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
May 3, 2008
#13
  • May 3, 2008
  • #13
eickholt78 said:
yeah i know you set pressure with the line off, alls i am saying is when i hook the line up it is at 42 pounds, so with the line off i am at about 48
Click to expand...
Pressure with the line off should be 38-41 range...
 
You must log in or register to reply here.

Similar threads

Tunerstudio help / services
  • Kabuki_notch
  • Apr 26, 2026
  • Digital Self-tuning Forum
Replies
2
Views
375
Digital Self-tuning Forum May 2, 2026
Mustang5L5
Electrical 88 EEC Injectors batch firing ?
  • Dustin 86GT
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
655
Fox 5.0 Mustang Tech Jan 8, 2026
gkomo
R
Microsquirt tune for stroked 351W in a foxbody
  • roldy
  • Jul 26, 2026
  • Digital Self-tuning Forum
Replies
7
Views
417
Digital Self-tuning Forum Oct 25, 2026
roldy
R
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
393
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Custom tune?
  • Nostang25
  • Jul 13, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
840
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 17, 2025
FastDriver
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?