Input please!!!! Procharger

KidCapri50 · Nov 15, 2006

I polished my procharger, and while doing so, I noticed this pinhole in the casting. It's really small, will this present a major problem??

KidCapri50 · Nov 15, 2006

My buddy suggests we just romove the compressor housing and tap it out an install a small screw to seal it.

Kilgore Trout · Nov 15, 2006

Is it an actual leak or just cosmetic?

KidCapri50 · Nov 15, 2006

A tiny hole / leak

blacksheep-1 · Nov 15, 2006

It's actually leaking, like you can feel it? If so, then drilling and tapping might work, but what if the casting is thin in that area? it could make the problem worse. You might take it apart and have it welded, but that could warp the housing. The ultimate fix would be to replace the housing but thats $$$$.
I hate to say this, and to post it because I know I'll be slammed 6 ways to sunday, but........JB Weld
OK, I'm ducking now...................

NeverFastEngh · Nov 15, 2006

If you score the metal around it well enough then JB weld would work. I have used it on alot of things you wouldnt think would work, but they all did.

FalconGuy016 · Nov 15, 2006

A leak? I'm not sure what exactly the housing is related to in the operation of the supercharger but that sounds pretty catastrophic to me... I guess I'm not thinking of the same thing.

Pennywise2 · Nov 15, 2006

NeverFastEngh said:
If you score the metal around it well enough then JB weld would work. I have used it on alot of things you wouldnt think would work, but they all did.

If it is actually a leak use some JB weld and let it sit for a while.
Buying a new Procharger headunit is quite costly.

BennyBlown2v · Nov 15, 2006

http://www.alumaloy.net/

Seriously. Or, a lil spot of tig will fix it. Fix it with metal, not JB weld - JB might hold but won't be a perminant fix.

FalconGuy016 said:
A leak? I'm not sure what exactly the housing is related to in the operation of the supercharger but that sounds pretty catastrophic to me... I guess I'm not thinking of the same thing.

That pin hole is in the part of the blower where the air goes out. If the hole was in the part where the gears are....THAT would be very, very bad. Where it is, at worst, it's just not going to hold boost (but should make a wicked cool whistle lol); but, if it were in the oiled side it would leak and pretty quickly kill the blower by starving it of oil.

the98stang · Nov 16, 2006

BennyBlown2v said:
http://www.alumaloy.net/

Seriously. Or, a lil spot of tig will fix it. Fix it with metal, not JB weld - JB might hold but won't be a perminant fix.

That pin hole is in the part of the blower where the air goes out. If the hole was in the part where the gears are....THAT would be very, very bad. Where it is, at worst, it's just not going to hold boost (but should make a wicked cool whistle lol); but, if it were in the oiled side it would leak and pretty quickly kill the blower by starving it of oil.

WTF..."alumaloy"?!

I'd trust JB weld over that crap ANY day. Especially when it says "As seen on TV" LMFAO.

But really your best bet (with out okey riggin' it) is welding or replacing the housing.

cooper58d2002 · Nov 16, 2006

You might want to call procharger because it looks like it may be a defective casting maybe they would work with you. then again they could say it was due to the polishing

DTNODYA · Nov 16, 2006

JB weld makes some stuff that's for metal ... I used it on my Dad's muffler when it got a small leak and it fixed it with no issues ....

El Diablo · Nov 16, 2006

I'd say tig weld it, unless it's still under warranty. Call Procharger and see what they say...

KidCapri50 · Nov 16, 2006

I got her tig welded today! Problem solved
Thanks for the input, it was either tig it or some bubble gum.

blacksheep-1 · Nov 16, 2006

I assume you had to take it apart to weld it?

the98stang · Nov 17, 2006

KidCapri50 said:
I got her tig welded today! Problem solved
Thanks for the input, it was either tig it or some bubble gum.

Bubble-yum

jivepepper · Nov 17, 2006

JB it.

BennyBlown2v · Nov 17, 2006

the98stang said:
WTF..."alumaloy"?!

I'd trust JB weld over that crap ANY day. Especially when it says "As seen on TV" LMFAO.

But really your best bet (with out okey riggin' it) is welding or replacing the housing.

That stuff actually works quite well. Much better and less porus than typical braze filler.

deftsound · Nov 17, 2006

blacksheep-1 said:
It's actually leaking, like you can feel it? If so, then drilling and tapping might work, but what if the casting is thin in that area? it could make the problem worse. You might take it apart and have it welded, but that could warp the housing. The ultimate fix would be to replace the housing but thats $$$$.
I hate to say this, and to post it because I know I'll be slammed 6 ways to sunday, but........JB Weld
OK, I'm ducking now...................

+1 jb weld is good ****, my uncle fixed the cracked engine block on his boat with jb weld 6 years ago and its still holding to this day

BooWFO · Nov 17, 2006

Ok you already fixed it. But excatly where was it?
Were there any problems with it on the car before polishing? ie did it have the leak before?
Looked like a normal inculsion to me but whatdya I know... Only ran a foundry for 5 years.

Input please!!!! Procharger

New Member

New Member

Fried or Broiled ?

New Member

Member

New Member

New Member

Banned

New Member

Active Member

New Member

Member

Member

New Member

Member

Active Member

New Member

Please ask me how much my supercharger cost

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency