Installed my headlights

[5.0TailPipeHump]

Awhile back i made a thread if i should go smoked or clears and i went with clears and am really satified with the look,
it makes the car look alot more cleaner and gives it that wow effect!

The install was pretty easy and took about 1½ hours , the bolts on the top
part on the headlights were not fun taking off and putting back on.

Now i just need to adjust em and there good to go.

 

[leroy93lx]

They look great! Mine were somewhat of a PITA to get adjusted, but i got it. I also got mine 4 or 5 years ago when they first came out, so maybe the quality got better over time. Hopefully you have no issues. Looks good though!

 

[Foster9887GT]

How Do you Adjust them? Are the Fog Lights Adjustable?........BTW, They look good, makes her look like new...

 

[5.0TailPipeHump]

How Do you Adjust them? Are the Fog Lights Adjustable?........BTW, They look good, makes her look like new...

There is adjusters on the back , my dad has the tool to do it , iv never adjusted headlights bf , the thing were gonna use is a hex shape unit, i belive its 4mm and that goes into the bolt thats purtruding, then turn it to the desired positioning.
seems not that hard. but were gonna line it up against a wall on a flat surface when its all said and done.

thanks for looking guys!

 

[LB0193]

poor old notchy in the snow

 

[5.0TailPipeHump]

poor old notchy in the snow

Lol you mean poor fella is in the house cant drive his notch till the snows gone.

I cant wait till this white crap turns into water and evaporates.

 

[Kabuki_notch]

Lol you mean poor fella is in the house cant drive his notch till the snows gone.

I cant wait till this white crap turns into water and evaporates.

amen

 

[iwashmycar]

looks great! good choice for sure.

 

[jrichker]

I drove around for several days with the driver’s side headlight scanning the upper branches of trees for squirrels, owls and UFO’s. The headlight lens had extra slack between the retaining clip and the screw head which allowed the lens to shift around. Fixed that with some small washers between the screw heads and the bottom of the mounting hole. I would recommend that you find 2 extra adjustment screws per side - they are the ones with the hex ends on the end of the screw where it sticks through the mounting plate. That may help the alignment problems, as the stock setup only allows adjustment with 2 screws, and is hard to adjust in and down at the same time.

If you bought Genuine Ford headlights, the adjustment will be easy. If you bought reproduction headlights, they will be very difficult to align properly. I bought reproduction units the first time, and my headlights could not be aligned: they would shine up in the trees and across the road. I even had all 3 screws set up as adjustment screws.

The set of headlights I now have say "Ford" on them and they seem to line up properly.

The adjustment screws are upper inside and lower outside screws. If the headlights were re-assembled properly, they will have a 5/32" hex on the screw. You can use a 1/4" ratchet with a 5/32" socket. The upper screws can be reached with the hood up, while the lower screws may require you to lay on the ground in front of the car and reach them from the bottom.

To align the headlights, find a level spot with a wall 25-30 feet away. Disconnect the driver light and align up the passenger light so that the light pattern is slightly below of the actual centerline of the headlight. This is to illuminate the right hand side of the road. Reconnect the driver light and disconnect the passenger light. The driver light should be aimed so that the light pattern on the wall is inward about 6" and slightly below the centerline of the headlight. This keeps you from blinding the oncoming cars. Disconnecting and reconnecting the headlights helps to show which headlight is shining in what direction. Reproduction headlights may shine in several directions at the same time, making it very difficult to align them if both lights are on at the same time

One Stangnetter recommends putting a fender cover over the headlight that isn't being aligned. I like his idea, it's simpler than disconnecting the lamps.

 

[Anaconda]

Headlights look great!! What type of bulb are you using in the small light next to the headlight and wattage? I just bought the same lights for my 89, of course I want the brightest light possible. Thanks

 

[5.0TailPipeHump]

Headlights look great!! What type of bulb are you using in the small light next to the headlight and wattage? I just bought the same lights for my 89, of course I want the brightest light possible. Thanks

I think it might be 5 watts correct me if im wrong, the bulb is simalar to the one in your corner taillights , heres a pic of that bulb.

Thanks for the write up jrichker.

 

[LaserSVT]

 

[SVT32VDOHC]

Looks really sharp. I love those things!

 

[DanB93]

Awhile back i made a thread if i should go smoked or clears and i went with clears and am really satified with the look,
it makes the car look alot more cleaner and gives it that wow effect!

The install was pretty easy and took about 1½ hours , the bolts on the top
part on the headlights were not fun taking off and putting back on.

Now i just need to adjust em and there good to go.

Hey Tailpipehump now that you have had those lights awhile how are they? I am interested in a pair myself. What is the smaller light in the headlight? Is it a high beam or daytime running light?

 

[5.0TailPipeHump]

Hey Tailpipehump now that you have had those lights awhile how are they? I am interested in a pair myself. What is the smaller light in the headlight? Is it a high beam or daytime running light?

There not bad at all' iv yet to still get them adjusted but other than that there awsome' Id reccomend some silver stars to really light up the road with these.

The smaller light will come on when you flip your lights on ' its when i remove my ebrake handle and not flip the light switch that i only get the regular light in the housing to come on .

 

[DanB93]

Cool thanks