• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Installing headers this weekend

  • Thread starter Thread starter Waz900
  • Start date Start date Nov 2, 2005

Waz900

Member
Apr 22, 2005
41
4
18
Sewell, New Jersey
Nov 2, 2005
#1
  • Nov 2, 2005
  • #1
I am installing a set of BBK shorty headers into my 1992 LX mustang. Does anyone have any kind of inside tips or info to share? I am trying to go through this without any problems. I have just the stock ones on there right now and I have heard many horror stories about bolts snapping and whatnot. I appreciate in advance any info that you guys would like to share. Thanks in advance!
 

94 Cobra 5.0

Member
Sep 18, 2004
114
1
16
Ft. Riley, KS
Nov 2, 2005
#2
  • Nov 2, 2005
  • #2
pb blaster is your friend. spray all the bolts the night prior to allow time for soak in and spray them again before you go to pull them off.
 

bubba-dough

Active Member
Dec 28, 2004
1,044
2
38
Indiana
Nov 3, 2005
#3
  • Nov 3, 2005
  • #3
94 Cobra 5.0 said:
pb blaster is your friend. spray all the bolts the night prior to allow time for soak in and spray them again before you go to pull them off.
Click to expand...

Don't worry about the bolts breaking at the head. It is usually the studs on the collector end but that doesn't matter because you have new headers. Also don't use cheap paper gaskets, use the metal ones.
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Nov 4, 2005
#4
  • Nov 4, 2005
  • #4
Agreed with all posts above, except you might have better access for removal and installation if you remove the spark plugs first....
 
1

1SLO306

My 97 GTP owns you ALL!
Mar 31, 2005
904
1
17
Muhlenberg, ky
Nov 4, 2005
#5
  • Nov 4, 2005
  • #5
ss93cobra said:
Agreed with all posts above, except you might have better access for removal and installation if you remove the spark plugs first....
Click to expand...
always easier shortys are easy to install. LT's are the bizatch!
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Nov 4, 2005
#6
  • Nov 4, 2005
  • #6
blake89stang said:
always easier shortys are easy to install. LT's are the bizatch!
Click to expand...
If you take the motor mount nuts off, and jack up on side and then the other accordingly, long tubes aren't that bad. You most likely have to come in from the bottom though...
 
1

1SLO306

My 97 GTP owns you ALL!
Mar 31, 2005
904
1
17
Muhlenberg, ky
Nov 5, 2005
#7
  • Nov 5, 2005
  • #7
i have the flowtech LT's on my car. the LH side is not thats hard to put in ir remove. the RH side is the one i hate. It comes apart in 4 pieces before it come off. But i have had alot of start probs so i have it down pat now!!!
 

CarFreakGT

20+ Year Stangneter
May 26, 2003
395
11
29
Louisville, KY
Nov 5, 2005
#8
  • Nov 5, 2005
  • #8
When I did mine, I took the front tires off. It just made it so much easier to get around under the car when it was up on jacks. Just be patient w/ the rear bolts, esp. on the passenger side, they're kind of tough to get to.
 

65ShelbyClone

Founding Member
Sep 9, 2000
4,675
38
119
Antelope Valley, SoCal
Nov 5, 2005
#9
  • Nov 5, 2005
  • #9
I pulled the intake hose off along with the rubber smog hoses on the passenger side when I installed shorties on my '89 GT. Liquid Wrench was handy, but I didnt break any collector bolts. I didnt pull the wheels off or lift the engine either. Might have been easier if I did, though.
 

vikingpower

New Member
Dec 6, 2004
656
0
0
CWU Ellensburg, WA
Nov 5, 2005
#10
  • Nov 5, 2005
  • #10
shorty's are nuthin compared to LT's. Should be pretty easy in my opinion
 
You must log in or register to reply here.

Similar threads

4
Drivetrain Wilwood Clutch and Brake Pedal Combo Installation - Help
  • 427stang
  • Jul 8, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
126
Fox 5.0 Mustang Tech Jul 8, 2026
427stang
4
M
a Pro-M EFI system
  • maximilian macdoanald
  • Feb 6, 2026
  • Digital Self-tuning Forum
Replies
7
Views
1K
Digital Self-tuning Forum Jun 5, 2026
X-cam34
X
C
Engine 01 gt
  • Carboni
  • Jun 28, 2025
  • SN95 4.6L Mustang Tech
Replies
6
Views
312
SN95 4.6L Mustang Tech Jul 19, 2025
nickyb
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
R
bbk shorty header to mid pipe gasket
  • randyyy
  • Sep 29, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
503
1996 - 2004 SN95 Mustang -General/Talk- Sep 29, 2025
randyyy
R
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?