• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Intake Spacer

  • Thread starter Thread starter backfocus
  • Start date Start date Apr 4, 2006

backfocus

Member
Sep 3, 2004
254
3
18
Little Rock, AR
Apr 4, 2006
#1
  • Apr 4, 2006
  • #1
I have a GT40 Upper and lower intake, recently had to remove the upper and replace the space as it was wearing out from years of heat damage and minor cracking that was causing a vacum leak. I replaced it with a new BBK spacer, but now my throttle cable bracket will not fit back properly. I know I could cut the bracket as many people do, but I don't want to.

My old spacer was 3/4" thick, the new BBK is 3/8" thick. I have looked at cannot find a 3/4" spacer anywhere, but I see that Trick Flow makes one that is 1" thick. Will the 1" spacer fit under a stock hood? Anybody using the same setup? It was tight before with the 3/4" spacer. I also have the FRPP stamped aluminum valve covers, which are taller and why the bracket will not fit.

And one last thing someone gave me another 3/8" spacer for a GT 40 type intake, but it does not have a hole in the center like mine does. What is this off of, Cobra? I see some Cobra intakes with the center hole.
 

lxwants12's

New Member
Sep 22, 2004
506
0
0
Apr 4, 2006
#2
  • Apr 4, 2006
  • #2
1 inch will not work with the stock hood
 

RYC CUKR

Founding Member
May 19, 2002
1,437
1
38
Orlando
Apr 4, 2006
#3
  • Apr 4, 2006
  • #3
I had a 1" spacer and I could close the hood but it rubbed the underside in a few spots. The best way to check to see if it will clear is to take some playdough and put a big wad of it on the parts that you think will hit the hood. Close the hood and then open it back up. Measure the thickness of the playdough and you have a pretty good idea of your clearances.
 

backfocus

Member
Sep 3, 2004
254
3
18
Little Rock, AR
Apr 4, 2006
#4
  • Apr 4, 2006
  • #4
Great little trick RYC, I will try that!!!
 
9

92stangg

New Member
Apr 2, 2005
36
0
0
Apr 4, 2006
#5
  • Apr 4, 2006
  • #5
i didnt have a problem with the 1inch spacer at all
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Apr 5, 2006
#6
  • Apr 5, 2006
  • #6
my 3/8 bbk spacer didn't come with the egr hole drilled in the center, I had to drill out a hole.

I have a stock throttle cable setup, but it bolted on just fine.
 

$uperstang

New Member
Jul 20, 2004
476
1
0
Detroit, MI
Apr 5, 2006
#7
  • Apr 5, 2006
  • #7
All intakes will vary as far as clearance with the 1" spacer. I know with a cobra, the spacer and the stock hood it clears.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,374
18,121
224
Massachusetts
Apr 5, 2006
#8
  • Apr 5, 2006
  • #8
I drilled a hole into my BBK 3/8" spacer too.

If you ever want to block it off again, take a razor blade, slide off the fat end and rtv it down to the intake and then slap all the gasets on.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Apr 5, 2006
#9
  • Apr 5, 2006
  • #9
I dont think a GT40 intake will clear- my Exploder intake won't
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Apr 5, 2006
#10
  • Apr 5, 2006
  • #10
fyi, i've measured the stock vs explorer intake, and they're the same height
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Apr 5, 2006
#11
  • Apr 5, 2006
  • #11
I've never tried to put a stock hood on my car, but there's no way on God's green earth it will fit with a 1" spacer... at least not from what my eyes can see lol
 

backfocus

Member
Sep 3, 2004
254
3
18
Little Rock, AR
Apr 5, 2006
#12
  • Apr 5, 2006
  • #12
Like I said before I used to have a 3/4" spacer and it fit fine. But I know when I bought the car it had a pushed up ding in the hood from where it looks like the hood hit the intake. Don't know if they tried to use a 1" spacer or not I have owned the car for 13 years now. Just wish I could find another 3/4" spacer. I am thinking about trying my extra spacer with the current 3/8" spacer, I think with the gaskets it will be close to 3/4". I will use 3 gaskets instead of 2.

Do you think that would seal right?
 

RYC CUKR

Founding Member
May 19, 2002
1,437
1
38
Orlando
Apr 5, 2006
#13
  • Apr 5, 2006
  • #13
I think that it would seal fine. I would give it a shot. The worst thing that could happen is that it wouldn't seal well and you would have to use the 1" or modify the throttle cable bracket. No harm in trying the 2 spacers together.
 
You must log in or register to reply here.

Similar threads

SOLD Trick Flow Box R Series Upper Intake w/90 mm Inlet
  • Habu135
  • Apr 30, 2026
  • Engine and Power Adder
Replies
2
Views
400
Engine and Power Adder Aug 19, 2026
Habu135
B
Front window issues
  • bruno
  • Nov 7, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
210
Fox 5.0 Mustang Tech Tuesday at 10:26 PM
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Electrical 91 hatch wiring help needed
  • FastDriver
  • Apr 7, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
275
Fox 5.0 Mustang Tech Apr 8, 2026
FastDriver
Exhaust 1 3/4” Long Tubes on a Fox Body AOD – Easiest route?
  • 5.0 Mike
  • Mar 19, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Mar 21, 2025
5.0 Mike
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?