it cost $721

REPSOL · Mar 16, 2004

well, there is been a whining/howling noise coming from my 2000GT rear end.

i have try alot of cheap way trying to fix it, like replace axle bearing, change oil...etc. but nothing helps.

Finally took it to the dealer, they said (as i have suspected) the pinion bearing and carrier bearing need to be replaced. and it will cost $721. lower then i expected.

hopefully this will fix this annoying noise.

btw, where is this carrier bearing?

YallarStang · Mar 16, 2004

I'm no expert, but it sure seems like you could damn near get the whole rear end replaced for that price.

new22003 · Mar 16, 2004

Crikey thats expensive. Might look in to other prices.

04DarkShadowGT · Mar 16, 2004

i agree sounds too much. you can get a whole new diff, gears, install kit, axles for probably $800+labor which would be maybe $500. just guessing

madmatt · Mar 16, 2004

I would have to agree, you could buy a pretty nice 31 spline set up and some gears and stuff and have it installed for a little more than that.

Aaron 4.6 · Mar 16, 2004

Carrier bearings. Plural. The carrier is what holds the differential. I have the same noise, and I have long suspected my front pinion bearing.

You are getting raped by Ford. The parts should be 20-30 bucks a bearing, tops. 2 pinions, 2 carriers, and 2 axle would put ALL new rear bearings in the $150-200 range of parts cost. A competent technician at a transmission shop should be able to do a full bearing swap in about 3-4 hours. Paying ~$70 an hour would cost you 200-300 in labor.

No way the total bill should be more than about 400-500.

GoBabyVroommm · Mar 16, 2004

F... the dealer. Take it to a speed shop and see what they can do for you. Had a friend take there car to a dealer for that problem and they messed up on it. The whining was louder after it got fixed.

REPSOL · Mar 17, 2004

Aaron 4.6 said:
Carrier bearings. Plural. The carrier is what holds the differential. I have the same noise, and I have long suspected my front pinion bearing.

You are getting raped by Ford. The parts should be 20-30 bucks a bearing, tops. 2 pinions, 2 carriers, and 2 axle would put ALL new rear bearings in the $150-200 range of parts cost. A competent technician at a transmission shop should be able to do a full bearing swap in about 3-4 hours. Paying ~$70 an hour would cost you 200-300 in labor.

No way the total bill should be more than about 400-500.

well too late, they quoted me on 1:30pm and the car was ready by 3:30.

on the bill it said $450+ for labor, and you are correct only about 300 bucks for parts. man they charge 17+ bucks for the diff oil need 4 qts!! man last time i change the diff oil it only take 2. oh well.

now the car is so quiet, i am very happy with it. even the wind noise (coming from the rt rear seatbelt hole )which has always been there was gone too.

i think they have sold me a car with problems in the 1st place

this is my 1st GT so i though a sport car are suppose to be noisy.

YallarStang · Mar 17, 2004

REPSOL said:
well too late, they quoted me on 1:30pm and the car was ready by 3:30.

on the bill it said $450+ for labor, and you are correct only about 300 bucks for parts. man they charge 17+ bucks for the diff oil need 4 qts!! man last time i change the diff oil it only take 2. oh well.

now the car is so quiet, i am very happy with it. even the wind noise (coming from the rt rear seatbelt hole )which has always been there was gone too.

i think they have sold me a car with problems in the 1st place

this is my 1st GT so i though a sport car are suppose to be noisy.

If my calculations are correct, that would be a labor rate of $225 per hour. Boy am I in the wrong business!

Dan_Soprano · Mar 17, 2004

BRO!!!!! Just do it yourself. that race and bearing are easy to change. Helps if you have a lift though............

REPSOL · Mar 17, 2004

YallarStang said:
If my calculations are correct, that would be a labor rate of $225 per hour. Boy am I in the wrong business!

oh no, they charge by the book. 1 of my friend works at a Honda dealer. All the jobs has a set hr chargable. if the machanic can finish a 2 hrs job in 1 hr he still get pay for 2hrs. my friend told me at one time he finished 20 some hrs of job in 8 hr day.

REPSOL · Mar 17, 2004

Dan_Soprano said:
BRO!!!!! Just do it yourself. that race and bearing are easy to change. Helps if you have a lift though............

i would have done it myself, if i know how.
my friend is a machanic, he said there are pre-load for the gears and the limited slip thing. he said too much a job to be done at home.

it cost $721

REPSOL

New Member

YallarStang

New Member

new22003

New Member

04DarkShadowGT

Member

madmatt

Ellis Juan sympathizer

Aaron 4.6

GoBabyVroommm

Active Member

REPSOL

New Member

YallarStang

New Member

Dan_Soprano

REPSOL

New Member

REPSOL

New Member

Similar threads

it cost $721

New Member

New Member

New Member

Member

Ellis Juan sympathizer

Active Member

New Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency