jerkyness when into the throttle..?

Paul Perreca

New Member
Mar 30, 2005
1,085
0
0
When im in first, and i get on it a little bit, like the wheels just spin, and thats ok it was expected, now when i shift into second fast n gun it, the car like feels like it dies and jerks tryna go - n then when it finally "catches" than it flies again - could this be the clutch because i haven't broken it in yet? it has only 250 miles on it now along w/ the engine - or is my engine making too much power for the trans or something? This is kinda bothersome, i figured i'd just keep breakin in the motor n ride it out, hoping this problem corrects itself!
 
oh yea, i did this twice by the way, cuz i'm trying to break the motor in the correct way - i have not been whipping this things ass, but it sounds soooooooo good w/ some throttle lol but yea, don't get the wrong idea - and it is not wheel hop in case anyone was thinking my tires were spinning wheel hop when i shifted
 
Paul check your setting on the TPS sensor to make sure you getting a good #..should be from .8-.99Volts with engine warm and off with ignition on. Then with the volt meter still hooked up watch the reading as you open the throttle by hand with the throttle linkage and watch the reading..it should increase smooth from your first setting to near or over 4.5volts at WOT. Definately pull the codes and see if you have any both with key on engine off, and key on engine on...and both times your checking with the engine at running temp. A new engine will not buck simply because it's new..something is causing the problem and it's likely electrical if the engines running fine at all other times. You may also want to get a fuel pressure gauge on the car to see if your pump is falling off when you drop the hammer..if pressure drops the car will hesitate as stated as well.
 
Also note...you can pull the IAC and clean it with carb cleaner and see if that helps, also check the bay for broken or forgotten vac lines buddy. Now should all else fail I might want to try another MAF or go back to the 19's and stock meter to see if perhaps the C&L is having issues.
 
yea man it's still stock fuel pump w/ 24 lbers - maybe thats it - i dunno how to check the codes, but i'll figure it out - i might take it to my diagnosis shop - they'll pull the codes for me prob - i can def check that voltage though
 
I would head to autozone or where ever to get a code reader..best 40$ I've spent. I'm leaning towards a bad TPS setting right now unless you've previously set it, because unless I'm wrong you did upgrade your TB and had to install the TPS that was in use...or a new one...it may need to be set. My TPS did not have enough range in movement when I loosened the phillips screws to get the correct setting I wanted .93v. What I did was open up the plastic holes with a drill bit (little bit at a time) untill I could move the TPS around enough to get me desired voltage.
 
Dump the codes and see what the computer says is wrong…

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great.

See http://www.troublecodes.net/Ford/
OR
See http://www.mustangworks.com/articles/electronics/eec-iv_codes.html

IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.

Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Walmart.

Or for a nicer scanner see http://www.midwayautosupply.com/detailedproductdescription.asp?3829 – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $35.
 
the new throttlebody from prof prod. came w/ a tps sensor bolted on already - my friend told me to drill those holes n i didn't believe him lol i was like HELL no i aint drillin into it lol thanks man - i think i'll buy the code dumper! what is it called, the ppl at my autozone are girls or stupid ricer guys n have no idea what i'll be talking about
 
I was also thinking you may have to tackle the idle set a couple times before the computer comes to agree with what you want it to do as a result of the cam. Mine was a mother to get right and I have to keep the idle between 850 and 950 to keep things in their happy place. I do recall setting the idle and resetting the computer maybe a half dozen times untill I was happy with the result. To this day I still enjoy hot start surges that require me to "work" the throttle a little bit to get the idle in check, once it settles post hot start it's more than good to go. Cold start the car is perfect every time. You MAY find it does surge a bit during stop and go driving once up to temp..I've found if you leave things as is the surging will subside as the computer becomes more accepting of the situation.
 
I have the same code reader but theres no LCD screen, mine was the red flash and beeping kind which works awesome especially for like 12 bucks from Walmart. If ur in a hurry or got the money i would get the kind he mentioned, looks alot simpler and easier. You dont have to worry about Oh S*** was that 5 beeps or 6 beeps or anything it tells u on the screen what it is.
 
Getting back to the original post, you said the wheels are spinning while the throttle response is jerky? Honestly, my vote is going to wheel hop here if that's the case. Do you have the quad shocks still on the car, or any aftermarket control arms?
 
no quadshocks - and it's def not wheel hop - it's the car like dying lol like feels like its borderline stalling out - but does it like 4 times right in a row real fast, like jerky, i do get wheel hop also, but this is totally differnet - !
 
but is it possible that this TPS is causing all this gay bucking?? It bucks super bad when shifting hard n fast while well into the throttle, but it also bucks quite a bit while just cruising, it's an annoying buck, not super hard like while almost full throttle, but it definately feels like it feels when you are going way to slow for a gear- like going 5 mph in second gear, it bucks but that's normal cuz of going to slow, but the car does it when i'm in the right gear just cruising at the right speed-
 
listen, i just checked it, the screws werent even tight at all, i didn't loosen them, yet i could turn the tps by HAND~! SOOO - i turned the car on, and let it idle, but it was surging, so i got out, moved that sensor and it smoothed out n the idle dropped from 1400 to 1100 and was smooth- the car was already kind of warm though - SOOO - i tightened it right there becausei don't have a voltmeter, and than i took it fora ride, it did NOT buck in any gear, and wheni opened it up, the tires let loose and massive wheel hop occurred - which is sweet (not the wheelhop) but the fact that it is not bucking right now- i will be driving it tonight, and will update if it starts bucking while cruising or not -

Hers what i figured - the vibration from the engine was making that sensor move becasue it was so loose - causing my problems, and also causing the fact that sometimes it bucked n sometimes it didn't -

could this be...? lol thanks