Leaky Breather

Under full throttle/hard acceleration/high rpms, there is very little/no vaccuum. However, those rockers are throwing a lot of oil. :nice:


It's not on your cold air intake. If you look at your throttle body, you'll see a capped vaccuum port on top. That's where it goes. Ideally, you would put on a set of valve covers designed for a fuel injected motor which will have the baffle and the filler tube and vac port. However, I forget which rockers you have and they may not clear the baffle.



Its raining today....its stopped but roads are wet so I can't really take a test drive to see if the new breather has helped the leak. It doesn't help that the hole for it is right on top of a rocker!

I picked up another breather....a closed one with a port on it. I'm gonna try it on there with a vac hose going to the spot you indicated and see if it makes any differences.

Technically, if anything it should run better having the air return to the system rather than the environment. Also have the stuff to add an oil separator inline with the PCV line....and grabbed a new PCV while I was at it.

Not sure what lifters are on it....might have some specs on them somewhere in my files.
 
The current issue is kinda like having a bad cut and no matter what brand of band-aid you use, it gets soaked through in a few minutes. It's not the band-aids' fault ; getting some stitches would be the solution.

I would figure out a way of having a baffle and the breather should be a lot more effective and less messy.
 
Its raining today....its stopped but roads are wet so I can't really take a test drive to see if the new breather has helped the leak. It doesn't help that the hole for it is right on top of a rocker!

I picked up another breather....a closed one with a port on it. I'm gonna try it on there with a vac hose going to the spot you indicated and see if it makes any differences.

Technically, if anything it should run better having the air return to the system rather than the environment. Also have the stuff to add an oil separator inline with the PCV line....and grabbed a new PCV while I was at it.

Not sure what lifters are on it....might have some specs on them somewhere in my files.

I don't know what you mean by a closed breather but if it can pull in outside air, you don't want to hook up that vac hose. Then you'll have a rather big vac leak right in front of the throttle body butterfly. The only way to do it right is to switch to an efi valve cover with the fill tube and baffle. Or just remove the pcv system and run breathers in both valve covers.
 
Ok....right now I have the "stock" PCV setup running.

I have an open breather (has vents in the breather itself) running which is tight and not sloppy like the old one.

So far, no oil pushing back up out the breather. I might run it like this and see how she does. Dunno if the vacuum will get messed up by having this breather in the valve or not. This breather has a built in "baffle" and at least doesn't splash from the rocker as easy.


When I say closed breather...I guess breather is a bad term, but it has no access to outside air.
 
You mean a sealed cap? Can you post a picture?

The eec will try to adapt for the vaccuum leak. Yours sounds like it's within the range it can adapt for since its not surging.


This is what I mean by closed vs. open


open

3434112ERL.webp



closed


3434110ERL.webp




With the closed, I would run the line to the air inlet before the TB fuel blades. I would make sure the breather had some sort of baffling built in it along with a separator inline to make sure oil isn't getting through too badly. This would at least close up the system I'd think.
 

Attachments

  • 3434112ERL.webp
    3434112ERL.webp
    50.1 KB · Views: 97
  • 3434110ERL.webp
    3434110ERL.webp
    53.9 KB · Views: 100