Location of Seat Restraint Module - 2001 Cobra

On an ’01 Cobra (New Edge) the “Seat Belt/Restraint Control Module” is part of the RCM (Restraints Control Module) system — the same module that handles the airbags.


Location:

It sits inside the car, center of the floor, under the dash console area.
Specifically, it’s bolted to the transmission tunnel just ahead of the shifter, under the center console.
Look for a small rectangular aluminum box with a big yellow connector (yellow = airbag/RCM circuits on Fords).

Things to note:

If mice chewed the harness, it’s often in the center console harness run or the kick panel harnesses where they like to nest.
The buckle sensor wiring usually runs under the seats into the same harness path that ties back into the RCM under the console.
Fuse 36 (10A) feeds that circuit, so if it’s blown, inspect the harness for a short-to-ground before replacing the fuse.

Safety:

Disconnect the battery and wait 15–20 minutes before working with the RCM or its wiring. The airbags hold charge from capacitors even after key-off.
Don’t probe the yellow connector directly with a meter unless you know you’re on non-airbag pins.

2001 Mustang Cobra RCM (Restraints Control Module) Connector C2040 Pinout​

Power & Grounds

• Pin 1 – Circuit 611 (BK/LB): Ground
• Pin 13 – Circuit 57 (BK): Ground
• Pin 14 – Circuit 37 (YE/LG): Fused battery power (Fuse 36, 10A)
• Pin 26 – Circuit 361 (PK/YE): Ignition power (hot in run/start)

Air Bag Deployment Circuits

• Pin 2 – Circuit 619 (DB/OG): Driver Air Bag – Stage 1
• Pin 3 – Circuit 623 (GY/OG): Driver Air Bag – Stage 1
• Pin 4 – Circuit 624 (GY/LG): Driver Air Bag – Stage 2
• Pin 5 – Circuit 625 (LB/OG): Driver Air Bag – Stage 2
• Pin 6 – Circuit 617 (OG/YE): Passenger Air Bag – Stage 1
• Pin 7 – Circuit 618 (LB/YE): Passenger Air Bag – Stage 1
• Pin 8 – Circuit 626 (DB/PK): Passenger Air Bag – Stage 2
• Pin 9 – Circuit 627 (LB/PK): Passenger Air Bag – Stage 2

Sensor Inputs

• Pin 10 – Circuit 614 (GY): Left Front Impact Sensor
• Pin 11 – Circuit 615 (DG): Left Front Impact Sensor
• Pin 12 – Circuit 616 (LB): Right Front Impact Sensor
• Pin 15 – Circuit 613 (PK): Right Front Impact Sensor

Seat Belt Pretensioners

• Pin 16 – Circuit 631 (GY/YE): Driver Pretensioner
• Pin 17 – Circuit 632 (OG/YE): Driver Pretensioner
• Pin 18 – Circuit 633 (DB/YE): Passenger Pretensioner
• Pin 19 – Circuit 634 (PK/YE): Passenger Pretensioner

Miscellaneous / Diagnostics

• Pin 20 – Circuit 57 (BK): Ground (diagnostic reference)
• Pin 21 – Circuit 57 (BK): Ground (diagnostic reference)
• Pin 22 – Circuit 815 (PK/LG): Warning Indicator Output (Seatbelt/Airbag Lamp)
• Pin 23 – Circuit 1047 (GY/OG): SCP Communication (+)
• Pin 24 – Circuit 1048 (PK/LB): SCP Communication (–)
• Pin 25 – Circuit 57 (BK): Ground

Important safety reminder: Never probe the squib (air bag deployment) circuits directly with a meter — they’re sensitive and you don’t want to trigger a bag. Use back-probing only on power/ground/communication pins, and keep the battery disconnected for at least 15–20 minutes before unplugging the module.

mzbhavn said:

Thanks a bunch for your help. You went into such great detail.

Click to expand...

Well, I'm no expert on your model year so I posted all the info I could find as it relates to your issue.