• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

MAC Cold Air Intake Question

  • Thread starter Thread starter RADA
  • Start date Start date Jun 19, 2004
R

RADA

New Member
Jun 1, 2004
36
0
0
Tucson, AZ
Jun 19, 2004
#1
  • Jun 19, 2004
  • #1
Sup Guys!

My car came with the MAC CAI already installed, I don't have any of the instructions for it. I tried to go to the Instructional PDF on the MAC site, but the link is hosed.

So my NOOB questions are; "What's the best/easiest way to take the filter out, what do I use to clean it, and do you use oil on them like a K&N?

Thanks,

RADA
 
M

moreause

New Member
Dec 24, 2003
74
0
0
Jun 19, 2004
#2
  • Jun 19, 2004
  • #2
if you leave the car on the ground is't kind of hard but not impossible...that's the way i put mine in. To get it out you need a flat screw driver or a driver to unscew the...sorry don't know this one in english...it's a ring with a scew, like the other one that old the silicone joint. The hard part is that you can only get one hand at the time in the fender...unless you get the inner fender out. And yes it doesn't to fit in there a had to crush mine a bit to get it in.

For the cleaning i'm not exactly sure but i think it's exactly the same as k&N but make sure you don't put to much oil i have heard about some maf contamination due to too much oil in the filter.
 

Blev

New Member
Aug 17, 2003
1,295
1
0
So. Cal. V-Town
Jun 19, 2004
#3
  • Jun 19, 2004
  • #3
RADA said:
Sup Guys!

My car came with the MAC CAI already installed, I don't have any of the instructions for it. I tried to go to the Instructional PDF on the MAC site, but the link is hosed.

So my NOOB questions are; "What's the best/easiest way to take the filter out, what do I use to clean it, and do you use oil on them like a K&N?

Thanks,

RADA
Click to expand...

I have the BBK set-up, but it's the same thing.

First: You need to take the 2 screws out of the bottom that hold the heat shield in place. This is the metal piece that seperates the engine from the fender.

Second: Loosen the 8mm bolt on the hose clamp that secures the filter in place. You can then slide it off and let it fall down into the fender.

Third: Plop your butt down on the ground in front of you tire and reach under the car and grab the filter out. You put your hand up under the bumper to get it. You can see the opening from above the car.

To put it back, is revers of what you did to remove it except you may need someone to grab the filter from up top while you hand it to them. I was able to put in on myself though.

There is a kit that is made to clean the filter that costs about 12 bucks. Most auto part stores carry it since alot of ricers use the filters.

Hope this helps.
 
R

RADA

New Member
Jun 1, 2004
36
0
0
Tucson, AZ
Jun 19, 2004
#4
  • Jun 19, 2004
  • #4
Thanks Guys
 

propellerhead

New Member
Apr 13, 2004
1,541
0
0
"but what's with the but shots?"
Jun 19, 2004
#5
  • Jun 19, 2004
  • #5
This is why I chose the K&N FIPK.
 
I

inferno9898

Member
May 17, 2003
249
1
18
Jun 19, 2004
#6
  • Jun 19, 2004
  • #6
Blev said:
Most auto part stores carry it since alot of ricers use the filters.
Click to expand...

 
You must log in or register to reply here.

Similar threads

Cold Air Intake options, is this filter fine or......
  • from6to8
  • Aug 10, 2024
  • 1994 - 1995 Specific Tech
  • 2
Replies
21
Views
2K
1994 - 1995 Specific Tech Sep 7, 2024
from6to8
  • Locked
SOLD Maximum Motorsports MMTR-2 Bumpsteer Kit - 1979 - 1993 Mustang
  • AeroCoupe
  • Apr 18, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
5
Views
620
Fox Body Mustangs For Sale (1979-93) Wednesday at 6:28 PM
AeroCoupe
J
Hello all, I have returned from a hiatus... Update and Questions
  • JackH
  • Aug 13, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
6
Views
345
1974 - 1978 Mustang II Talk & Tech Aug 15, 2025
JackH
J
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
526
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
216
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?