• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

more help....

  • Thread starter Thread starter olesneakypete12
  • Start date Start date Jan 22, 2008
O

olesneakypete12

New Member
Nov 8, 2007
8
0
0
willingham, all day everyday
Jan 22, 2008
#1
  • Jan 22, 2008
  • #1
With a 347, I had to bore my motor 30 over and i have the gt40 x heads...I guess my compression is about 10 1/2:1...?...will i be fine to run a vortech s trim superchager with this???? What power would i make...guess....
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
Jan 22, 2008
#2
  • Jan 22, 2008
  • #2
If you run the blower on it I woul only run 5-8psi.
The block isn't going to handle that kind of power. Unless your running an aftermarket block.
Should be in the 500hp range.
 
O

olesneakypete12

New Member
Nov 8, 2007
8
0
0
willingham, all day everyday
Jan 22, 2008
#3
  • Jan 22, 2008
  • #3
Is it pointless or would u do it??? Could i run 8 psi and spray a 75 shot on it?
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
Jan 22, 2008
#4
  • Jan 22, 2008
  • #4
I have a buddy doing the same thing. But he has and R302 block with the best of the best as far as internals. If you have the blower and everything allready I would say go for it. But the stock block will be on barrowed time.
 
O

olesneakypete12

New Member
Nov 8, 2007
8
0
0
willingham, all day everyday
Jan 22, 2008
#5
  • Jan 22, 2008
  • #5
My block is stock....how much hp will it handle?
 

88mouse

New Member
Apr 18, 2007
630
0
0
Mooresville nc
Jan 22, 2008
#6
  • Jan 22, 2008
  • #6
450-500hp. Another buddy of mine just cracked his block it was a 347 11:1. Spraying a 150 shot.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Jan 22, 2008
#7
  • Jan 22, 2008
  • #7
THAT IS ALOT of comp. for a blower but with a safe tune it might work keep the boost down though........... and run good fuel and cold plugs
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Jan 22, 2008
#8
  • Jan 22, 2008
  • #8
How did you calculate out your CR??
 
You must log in or register to reply here.

Similar threads

M
  • Poll Poll
Stroking a Mexico 289 or newer roller 302
  • MaryJaneTheMustang
  • Aug 12, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
162
1965 - 1973 Classic Mustangs -General/Talk- Aug 12, 2026
Bullitt347
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
295
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
508
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
328
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
720
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?