• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

More power

  • Thread starter Thread starter stevesLX
  • Start date Start date Jul 17, 2007

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Jul 17, 2007
#1
  • Jul 17, 2007
  • #1
O.K. guys need some help here. If you look at my sig or profile you will see what I have car wise. I am tryin to hit 12's on motor. My best time to date is a 13.29. I am looking for a very cheap and easy way to knock a few more tenths off. My setup currently is as follows: 89LX 302,Edelbrock 5.0 performer upper and lower,24# injectors, Fcam, 75MM TB, 73 MAF, Mac CAI, Lakewood 70/30 struts,Aluminum driveshaft, BBK long tube headers, 21/2 flowmaster exhaust, 3.73's, 245/45/17 Drag Radials. Some guys told me to take my belt off and it may break into the 12's. But thats a hassle to have to do that all the time, not to mention the car getting hot. I thought about perhaps a short belt but I tried to retofit one on there and it will not turn the water pump pulley like it should unless there's another trick that I am unaware of on routing it. I dont have A/C but I have power steering. I took the belt and stuck it on the crank brought it up the backside of the water pump pulley and around the alternator. But it barely makes contact with the water pump. Any suggestions would be great and much appreciated.
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Jul 17, 2007
#2
  • Jul 17, 2007
  • #2
What kinda of 60' times are you running? I imagine with drag radials you are getting out of the hole pretty quick. I'm not sure there is going to be a cheap and easy way to get much faster on motor. I seriously doubt that taking the belt off would add that much horsepower to propel you 3 tenths faster in the 1/4. My guess is you are pretty close to your limit without some serious mods to the engine. You might want to look into suspension upgrades. Everyone decides to do those last for some strange reason.
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Jul 17, 2007
#3
  • Jul 17, 2007
  • #3
My 60 Fts if the track is prepped well are 1.81 to 1.93
 

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Jul 18, 2007
#4
  • Jul 18, 2007
  • #4
Sub frame connectors migth help you out a little bit with getting those 60' times down a little bit. Perhaps upper and lower control arms out back. Every .1 off your 60' is approx .2 off your ET. So i would focus on suspension/Launch/shifting. Those are all pretty cheap mods that can net some nice ET gains. How much timing are you running...perhaps 93 octane and a couple more degrees?! What tire pressure are you running and what rpm are you launching and shifting at? What size drag radial?
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Jul 18, 2007
#5
  • Jul 18, 2007
  • #5
The other option would be to shed some weight out of the car.
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Jul 18, 2007
#6
  • Jul 18, 2007
  • #6
GT-40P heads would do it but they're going to be hard to find for really cheap. The stock heads are a bad mismatch for the rest of your parts.
 
S

Sicarius428

Active Member
Jan 6, 2004
2,085
5
49
Jul 18, 2007
#7
  • Jul 18, 2007
  • #7
The heads are holding you back quite a bit. I know its not a cheap solution though. I would look into some control arms and weight savings.
Kevin
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Jul 18, 2007
#8
  • Jul 18, 2007
  • #8
I can get a set of GT40P for 140.00 from a junk yard up the street here but I am not sure if they will work with the headers I am using. I am using BBK long tube headers. I have heard people say the spark plugs go straight in instead of an angle. Any insight on this.
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Jul 18, 2007
#9
  • Jul 18, 2007
  • #9
some edelbrock performer heads to match that intake would get you there easily .....electric fan as well
 

stevesLX

Member
Nov 12, 2006
373
0
16
cincinnati
Jul 19, 2007
#10
  • Jul 19, 2007
  • #10
I have a electric fan. And I gues I will just fogo the 12's for now and be happy with low 13's and save some money to get some good heads.
 
You must log in or register to reply here.

Similar threads

S
Engine Belt routing with supercharger and smog/ac/ps delete
  • Steve6482
  • Jul 15, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
157
Fox 5.0 Mustang Tech Jul 15, 2026
Steve6482
S
B
Idler pulley as substitute for Power Steering Pump ?
  • Bhenders
  • Jul 15, 2026
  • Other Auto Tech
Replies
5
Views
361
Other Auto Tech Jul 16, 2026
LILCBRA
Engine Themostat
  • Mindseye007
  • Jan 30, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
1K
Fox 5.0 Mustang Tech Feb 1, 2026
86HO5.0
8
Engine My Gates K060845 (85 1/4”) belt doesn’t fit
  • Mcmahst
  • Jun 26, 2025
  • Fox 5.0 Mustang Tech
Replies
17
Views
807
Fox 5.0 Mustang Tech Jun 27, 2025
Mcmahst
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?